KitchenAid KEBS208DWH1 Інструкція з монтажу - Сторінка 4
Переглянути онлайн або завантажити pdf Інструкція з монтажу для Духовка. KitchenAid KEBS208DWH1. KitchenAid KEBS208DWH1 5 сторінок. 30" electric built-in single and double ovens
Також для KitchenAid KEBS208DWH1: Перелік деталей (12 сторінок)
Друкувати сторінку
iiiiii!i E'ectrica'
connection
Electrical Shock Hazard
Disconnect power to the junction box before
making connection.
Electrically ground oven.
Connect ground with lO-gauge-minimum solid
copper wire.
Failure to follow these instructions could result
in death, fire or electrical shock.
This oven is manufactured with white (neutral)
power supply wire and a cabinet-connected bare
grounding wire twisted together.
Feed oven cable through opening in
• the cabinet. Make electrical connection
following the steps needed for your installation.
1. Disconnect the power supply.
2. Remove the junction box cover.
3. Connect oven cable to junction box through the
U.L.-listed conduit connector.
4. Connect the two black wires together with
twist-on connectors.
5. Connect the two red wires together with
twist-on connectors.
6. Complete electrical connection according to
local codes and ordinances.
junction
box _
red_
white _
w,re
_
grounding oven
cable wires --
factory crimped
Figure 1
cable from
power
supply
cable from
conduit
oven
connector
If local codes PERMIT
connecting cabinet-grounding
conductor to neutral white
wire in junction box:
7. Connect the factory-crimped
bare and white oven cable wires
to the neutral (white) wire in
junction box. See Figure 1.
8. Replace junction box cover.
cable from
junction
power supply
Figure 2
cable from
connector
oven
If local codes DO NOT PERMIT
connecting cabinet-grounding
conductor to neutral white
wire in junction box:
7. Separate the factory-crimped
bare and white oven cable wires.
8. Connect white oven cable wire to
neutral (white) wire in junction
box. See Figure 2.
9. Connect the bare grounding
oven cable wire to a grounded
wire in the junction box. See
Figure 2.
10. Replace junction box cover.
If connecting to a
four-wire electrical system:
7. Separate bare and white oven
cable wires.
8. Connect white oven cable wire
to neutral (white) wire in
junction box. See Figure 2.
9. Connect the bare grounding
oven cable wire to the green
grounding wire in junction box.
Do Not connect bare grounding
wire to neutral (white) wire in
junction box. See Figure 2.
10. Replace junction box cover.
i ii A.ac"ment
Carefully push against seal area of oven front
frame when pushing oven into cabinet.
Do Not push against outside edges.
• Lift oven into cabinet cutout using the
oven opening as an area to grip.
shipping
foot
Push against seal area of front frame to push
oven into cabinet until shipping feet almost
contact cabinet. Use a Phillips screwdriver to
remove screws attaching shipping feet. Remove
and discard shipping feet.
Push oven completely into cabinet and center
oven in cabinet cutout.
4 screws
• Important: Securely fasten oven to cabinet
using the screws provided (two screws for a single
oven or four screws for a double oven). Insert the
screws through holes in mounting rails. Do Not
overtighten screws.
Slide top
oftrim up.
_!
_
Push trim
into place.
Replace
trim screw.
Slide top end of each trim upward onto oven
side rails. Push each trim into place at bottom of
trim. Use screws to attach each trim to oven. Take
care not to scratch other surfaces with ends of trim.
• Replace oven racks.
Important: Replace the door with the model/serial
rating plate on the upper oven.
On some models, the construction of this door is
designed to withstand self-cleaning temperatures.
\
oven frame
hinge slot
oor
hinge
Replace the single or upper oven door by
•
inserting ends of hinges into hinge slots in
oven frame. Push behind each hinge so that hinges
are pushed into oven frame as far as they will go.
Open door and remove both door removal pins.
Close and open door to check that door closes and
opens completely. If door does not close or open
completely, you have not pushed hinges
completely into frame. Repeat door removal step
and reinsert door into hinge slots again.
Repeat for lower oven door.
II C "ec" o.eration
IO
• Turn on power supply. The display
panel will light up briefly. "PF" should appear in
the temperature display.
_ BAKE { BROIL i CLEAN
Check the operation of your single oven.
Press the "BROIL" pad. "BROIL" will appear in
the display. Press the "START" pad. Make sure the
oven door is closed and the "ON" light is shown in
the display area. After 2 minutes, partially open
oven door. You should feel heat from the oven.
Press the "CANCEL" pad.
Check the operation of your double oven.
Press the "Upper Oven" pad. Press the "BROIL"
pad. "BROIL" will appear in the display. Press the
"START" pad. Make sure the oven door is closed
and the "ON" light is shown in the display area.
After 2 minutes, partially open oven door. You
should feel heat from the oven. Press the
"CANCEL" pad.
Press the "Lower Oven" pad and repeat the steps
you completed for checking the upper oven.
If your oven does not heat or an "F", followed by
a number, appears in the display, contact your
dealer or check the "If you need service..." section
of this Installation Instructions.
To get the most efficient use
from your new oven, read your
Use and Care Guide. Keep Installation
Instructions
and Guide close to oven
for easy reference.
Page 3