KitchenAid KESC300BBL2 Інструкція з монтажу - Сторінка 4

Переглянути онлайн або завантажити pdf Інструкція з монтажу для Духовка. KitchenAid KESC300BBL2. KitchenAid KESC300BBL2 5 сторінок. 30" (76.2 cm) electric range with self-cleaning thermal/convection oven
Також для KitchenAid KESC300BBL2: Інструкція з використання та догляду (5 сторінок)

Друкувати сторінку

Excess,veVVe,ght

Hazard

IZD

Use two or more people to move and install

range.

Failure to follow this instruction can result

in back or other injury.

irmly grasp the range and gently lay it

on its back on the cardboard corners.

ull cardboard bottom and shipping base

firmly to remove.

Use an adjustable wrench

to loosen the leveling legs

1-1/2 turns.

lace cardboard or hardboard in front

of range. Stand range back up onto

cardboard or hardboard.

Tip Over Hazard

A child or adult can tip the range and be

killed.

Connect anti-tip bracket

to rear range foot.

Reconnect

the anti-tip bracket, if the range

is moved.

Failure to follow these instructions can

result in death or serious

burns to

children and adults.

Place the anti-tip

bracket template

on the floor in

the cabinet

opening so that

the left edge is

against cabinets

and the top

edge is against

the rear wall,

molding or

cabinet. If

25" (63.5 cm) counferfop

over

24" (61 cm) cabinet

\ _J,-

._J

J /onti-tip

_braekef

_template

countertop opening is deeper than 25 inches

(63.5 cm), measure and mark a distance 25

inches (63.5 cm) in from front of countertop

opening

and align template with mark

(or subtract 25 inches (63.5 cm) from countertop

depth and add the difference to the 2-1/4-inch

(5.7 cm) dimension).

25" (63.5 c

If countertop is

not flush to the

side of cabinet

opening, align

Counfeffop

overhangs

the left side of

cabinet side.

the template to

= Difference

allow for the

between

countertop

counterfop

depth

and 25"

overhang. Tape

(63.5cm).

the range anti-tip

bracket template

in place,

anti-tip

bracket

template

slide-in

cutout

shown

Control

panels may vary.

Contact

a qualified

floor covering

installer for

the best procedure

of drilling

mounting

holes

through

your type of floor covering,

Before moving,

slide range onto cardboard

or hardboard,

To mount anti=tip

bracket

to wood floor,

use the anti-tip bracket

template to mark

where to drill mounting

holes. Use a drill with a

1/8" (0.3 cm) drill bit to

drill the two holes.

Remove template from

floor.

To mount anti-tip

bracket to concrete

ceramic

floor, use the anti-tip bracket template

to mark where to drill mounting holes. Use a drill

with a 3/16" (0.48 cm) masonry drill bit to drill the

two holes. Remove template from floor. Tap

plastic anchors into mounting holes in floor with

hammer.

Line up holes in anti-tip

bracket with holes in floor.

Use the screws provided

to fasten anti-tip bracket

to floor.

NOTE: Anti-tip

bracket

must be

mounted

securely

to the

sub floor. Depending on the thickness

of your flooring, longer screws may be

necessary to anchor the bracket to the sub floor.

Longer screws are available from your local

hardware store.

i Move range close to cabinet opening.

Make electrical connection. See

[] "Electrical requirements" and

"Electrical connection," Panel B, for details. "8888"

should appear in the clock display. Refer to Use

and Care Guide for information on electronic

controls.

] Remove cardboard or hardboard from

under range. Carefully move range

[] into final position.

Press on front

of storage

drawer and

release to open.

Pull open to first stop position.

Lift front of drawer to clear white

wheels in drawer guides. Remove drawer and set

it aside on a protected surface.

113.1

Look under range

(a flashlight may

be needed) to

check that left rear

leveling leg is

engaged in the anti-tip

bracket. If leveling leg is

not properly engaged,

remove and reposition the anti-tip bracket to

insure that the leveling leg fits properly in the

anti-tip bracket.

oven. Place

level on rack, fir

to side; then front to back. If the range

is not level, pull range forward until the rear

leveling leg is removed from the anti-tip bracket.

Adjust the leveling legs up or down. Then slide

range back into position. Check that leveling leg

is engaged in anti-tip bracket.

NOTE: Oven must be level for satisfactory baking

conditions.

_ Insert storage drawer into slide rails

on sides of drawer opening. Lift front

[] of drawer slightly and push firmly to

close drawer.

] Push in and

turn each

= surface unit

control knob to "HI"

position. Check the

operation of the cooktop

elements and indicator

lights.

OFF

MED

I Check the operation of the oven

element. Press the "BAKE" pad.

[] "350°F '' will appear in the temperature

display. Press the "START" pad. "Lo" will appear

in the display; then "170°F '' (when oven reaches

170°F).

The bottom element should glow red and the

indicator light should be on. The upper element

should become hot but not glow red. As the oven

temperature rises, the temperature in the display

will increase in 5°F increments until the oven

reaches the set temperature.

Press "CANCEL/OFF"

pad.

Check the operation of the broil

element. Close the oven door. Press the

[] "BROIL' pad. "500°F '' will appear in the

temperature display. Press the "START" pad.

Look through the oven window. The top element

should glow red. Press the "CANCEL/OFF"

pad.

To get the most

efficient

use from your

new electric

range,

read your

KitchenAid

Use and Care Guide.

Keep Instaflation

Instructions

and Guide

to the

electric

range

for easy reference.

Panel C