Gardena THS 400 Інструкція з експлуатації Посібник з експлуатації - Сторінка 5
Переглянути онлайн або завантажити pdf Інструкція з експлуатації Посібник з експлуатації для Тример Gardena THS 400. Gardena THS 400 9 сторінок. Electric telescopic hedge trimmer
Також для Gardena THS 400: Інструкція з експлуатації Посібник з експлуатації (11 сторінок), Інструкція з експлуатації Посібник з експлуатації (10 сторінок)
Друкувати сторінку
GARDENA Electric Telescopic Hedge Trimmer THS 400
1. Technical data
Power consumption, motor
W
a
Mains voltage
V
Frequency
Hz
Strokes
1/ min.
Cutting length
cm
Telescopic extension range
cm
Weight
kg
Working area related emission
characteristic value L
1)
dB (A)
pA
Noise level L
dB (A)
WA
Vibrations a
1)
ms
- 2
vhw
2. Notes on operating instructions
Please read these operating in-
operating controls, their correct
structions carefully and observe
use, and the notes on safety.
the notes given.
Use the instructions to familiarise
For safety reasons, child-
A
yourself with the equipment, the
ren under 16 as well as
persons not familiar with these
3. Proper use
The GARDENA Telescopic
Compliance with the instructions
Electric Hedge Trimmer THS 400
provided by the manufacturer is
is designed for cutting hedges in
a prerequisite for using the tool
domestic gardens and allotments.
correctly.
The operating instructions also
Gardening tools for private house-
include the conditions for opera-
holds and gardens are consid-
tion, repair and maintenance.
ered unsuitable for use in public
grounds, parks, sports centres,
in agriculture or forestry.
4. Assembly / setting the working position
!
4.1 Assembly of the guide
Trimming hedges from the
handle (fig. A)
side at a distance from the
The three-position guide handle
standing position, eg. to reach
1
is mounted onto the unit and
over flower beds (fig. B / B 1).
secured with 2 screws. (Captive
Note:
screws integrated in the handle.)
Telescopic handle retracted.
"
For trimming extremely low
4.2 Basic working position
hedges, or eg. ground blan-
settings (fig. B - E)
kets, while standing upright
The Telescopic Hedge Trimmer
(fig. C / C 1).
has three basic settings. These
Note: Telescopic handle
!
§
are marked
to
on the blade
extended to the appropriate
head and the handle:
length for upright working.
12
350
230
50 / 60
2,400
40
0 - 31
4.3
81
94
< 2.5
1) Measuring method according to EN 774
operating instructions should
not use this Electric Telescopic
Hedge Trimmer.
Keep these operating instruc-
tions in a safe place.
Attention! Because of
A
the danger of physical
injuries, this tool must not be
used for cutting lawns / grass
verges, or for cutting in the
sense of shredding for com-
posting.
(fig. A-G)
§
For trimming high hedges
up to approx. 2.5 m from
the ground without the need
for a ladder or scaffolding
(fig. D / D 1).
Note: Telescopic handle ex-
tended to the appropriate
length. Control of the Tele-
scopic Hedge Trimmer is
within arm's reach for easier
handling (fig. D).
G
4.3 Setting a working position
Attention! The mains plug
A
must be disconnected
and the cutting blade sheath
should remain in position when
setting the working position !
Never take hold of the cutting
blade to turn the blade head
or to extend the telescopic
handle!
Note: The cutting blade has
a total of 8 working positions
(12° increments from 0°/horizon-
tal to 84° elevation).
Adjustment to any of the 5 inter-
mediate settings for the 3 work-
ing positions described above
is made in the same manner.
!"
§
The positions
or
de-
scribed above are recommended
for straight forward handling.
Important! Always ensure that
the selected position snaps in
correctly. Danger of injury!
5. Operation
(fig. H / I)
The Hedge Trimmer is fitted with
a two-hand safety switch to pre-
vent the tool being turned on by
accident. Thus both hands are
required to operate the Hedge
Trimmer (fig. H):
1. Hold by the 3-point guide
1
handle
and press one of
the three button switches
3
2. Hold the grip
with the other
hand and depress the button
4
switch
. The Hedge Trimmer
will then start to run.
Simply release either of these
switches in order to stop the
trimmer.
In accordance with safety regula-
tions, an additional safety device
ensures that the blade motion
stops within 0.5 sec.
Select one of the basic working
!"
§
positions
or
according
to the description section 4.2 and
referring to figure E, adjust the
Telescopic Hedge Trimmer as
follows (fig. D / F/ G):
1. (Fig. F) Adjust the length of
the telescopic handle by
pressing and holding the ad-
6
justing button
while extend-
ing the telescopic handle to
the desired working length
(fig. F). The length of the tele-
scopic handle can be extended
by max. 310 mm.
2. (Fig. G 1) Press and hold the
7
oval pimpled button
while
A
turning the trimmer head
in
the axial direction into one of
!"
the working positions
or
§
§
for example into position
for trimming the top of a high
hedge (arrow must point to
the position number – see
figure D 1).
The projecting guide (impact
protection) prevents any
kick-back if the trimmer hits
a solid object.
Cable Lock / Extension Cable
(fig. I)
Loop the extension cable and
insert the loop into the cable lock
2
.
5
. This cable lock prevents any
accidental disconnection from the
power supply. Plug the connector
into the extension cable socket.
Safety Clutch (Slip-Clutch)
The safety clutch protects motor,
gear and blades from mechani-
cal damage caused by the
blades jamming. If the blades
are jammed by an object, discon-
nect the trimmer from the power
supply and remove the object.
G
Note: The trimmer head can
be set to one of 7 axial posi-
tions between 0° and 180°
at increments of 30°.
3. (Fig. G 2) Adjust the cutting
angle for the trimmer blade
by pressing and holding the
9
round adjusting button
while
adjusting the position of the
8
trimmer blade
for working
as required.
§
(Our example: position
.
Arrow must point to the position
number – see figure D 1).
Note: All 3 working positions
for selection can be set in this
way.
The working position has been
correctly set when the position
number indicates the selected
position (see example figure
D 1).
The safety devices in-
A
stalled by the manufac-
turer must not be removed
and / or bypassed, eg. by tying
down a switch in the handle.
Never use a tool which is not
complete or which has been
modified from its original
design.
To avoid unintentional start,
never carry the Telescopic
Hedge Trimmer at its button
2
switches
.
13