Avaya 3626 Series Короткий довідник - Сторінка 2
Переглянути онлайн або завантажити pdf Короткий довідник для Телефон Avaya 3626 Series. Avaya 3626 Series 2 сторінки. Wireless telephones
Також для Avaya 3626 Series: Короткий довідник (1 сторінок), Посібник з монтажу (19 сторінок)
Друкувати сторінку
Turning the Phone On and Off
•
To turn the phone on: Press
until two chirps sound (about one second).
The in-service tone sounds and your name and extension number is displayed. The phone is now in
standby mode, ready to make and receive calls.
•
To turn the phone off: While in standby mode, press and hold
phone turns off. The phone cannot be directly turned off during a call. End the call first and then turn
the phone off.
Making a Call
1.
Press
. This transitions your phone to active off-hook mode and there is a dial tone.
2.
When you have completed the call, press
mode. Be sure to do this at the end of each call.
Answering Calls
•
To answer a call: Press
and hold the earpiece to your ear and speak. When the call is
finished, press
.
•
To answer a call via the headset: With the headset plugged in to the phone, press either
9, * or #. When the call is finished, press
•
To answer an incoming call whilst on a call: Put your first call on hold (press FCN+3) and press
LINE and then press the line number of the second call. When the call is finished, press
Note
•
You can answer a call whether your phone is locked or unlocked.
Locking/Unlocking your Phone
•
To lock your phone's keypad: Press FCN and then press Select. From the standby menu, press
Lock.
•
To unlock your phone's keypad: Press Unlk and then press #.
Retrieving your Voicemail
, indicates that you have a new voicemail message.
A flashing
•
To retrieve your voicemail, dial *17.
Changing the Volume
•
To increase or decrease the volume whilst on a call or whilst the phone is ringing, press the Up or
Down buttons.
Activating Push-To Talk (PTT)
•
To initiate a PTT call, press the PTT button and briefly wait for the channel to activate. When
Transmitting is displayed, begin talking.
•
When your phone receives a PTT transmission, a 'receiving alert' sound is heard and the phone
enters receive state.
•
To terminate incoming broadcasts, press Terminate and at the confirmation prompt, press Yes.
PTT is immediately stopped and the phone exits the PTT session.
Enabling a Channel
You can enable any PTT channel by entering the corresponding number from the keypad. If PTT has been
enabled on the phone, the default channel is the lowest allowed channel.
Note
•
If PTT is enabled, the standby battery capacity is decreased to approximately 30 hours.
3626 Wireless Phone Quick Reference Guide
until one chirp sounds. The
to exit the active mode and return to the standby
.
.
Battery Life
Indicates the amount of charge remaining in the battery pack. When one level remains, the battery
pack need to be changed.
Battery Low
This message is displayed and an alarm sounds when the phone is in standee mode and the battery pack is
critically low. The phone cannot be used until the battery pack is charged.
Accessing the Softkeys
The softkeys operate with a toggle function. To
activate a softkey feature, press the left or right side of
the corresponding key.
For further softkeys, press More. The following screen
is displayed:
, 0-
Activating the Softkeys
The softkeys on your phone enable you to quickly activate system features. The display area above each
softkey is programmed with a feature abbreviation which are (from left to right), A, B, C and D.
To activate a softkey, press the left or right side of the corresponding key. The five softkeys are:
Transfer (Tran)
1.
With a call active, press the Tran softkey. A dial tone is heard.
2.
Dial the number you want to transfer the call to.
3.
When the call is answered, press the Tran softkey again, transfer completed is displayed.
Conference (Conf)
1.
To set up a conference call, dial the first party.
2.
When the first call is established, press the Conf softkey and dial the next party.
3.
When the call is answered, press Conf again. There are now three participants in the conference and
Conference 2 is displayed.
Hold
•
To place a call on hold, press the Hold softkey.
•
To retrieve a held call, press LINE and the corresponding line on hold (for example, 1)
Mute
•
To prevent the other person on the line from hearing you, press the Mute softkey. Mute is displayed.
•
To reinstate two-way conversation, press the Mute softkey again.
Redial (ReDL)
•
To redial the last dialed number, press the Redial softkey. The number is dialed automatically.
3626 Wireless Phone Quick Reference Guide