KitchenAid KHHC2090SBL - Architect 2.0 Cu Ft Microwave Oven Інструкція з монтажу Посібник з монтажу - Сторінка 8

Переглянути онлайн або завантажити pdf Інструкція з монтажу Посібник з монтажу для Мікрохвильова піч KitchenAid KHHC2090SBL - Architect 2.0 Cu Ft Microwave Oven. KitchenAid KHHC2090SBL - Architect 2.0 Cu Ft Microwave Oven 12 сторінок. Installation instructions

Друкувати сторінку

1. Product Dimensions

Attach Mounting Plate to Wall

NOTE: Secure the mounting plate to the wall at both bottom

corner holes drilled into the wall studs and/or drywall using either

1/4-20 x 3" round-head bolts and toggle nuts or 1/4 x 2" lag

screws.

Refer to illustrations in "Possible Wall Stud Configurations" in

"Locate Wall Stud(s)" section.

No Wall Studs at Corner Holes (Figures 1 & 2)

NOTE: The mounting plate must be secured to the wall on at least

1 wall stud as well as at both bottom corners.

1. With the support tabs of the mounting plate facing forward,

insert 1/4-20 x 3" round-head bolts through both bottom

corner holes of mounting plate.

2. Start toggle nuts on bolts from the back of the mounting plate.

Leave enough space for the toggle nuts to go through the wall

and open.

A. 1/4-20 x 3" round-head bolt

B. Mounting plate

C. Spring toggle nut

3. Position mounting plate on the wall, making sure that the top

of the mounting plate is aligned with the front edge of the

upper cabinet.

4. Push the 2 bolts with toggle nuts through the drywall, and

finger tighten the bolts to make sure toggle nuts have opened

against drywall.

A. 1/4-20 x 3" round-head bolt

B. Mounting plate

C. Drywall

D. Spring toggle nut

5. Insert lag screw(s) into the holes drilled into wall stud(s) in

Step 2 of "Installation for No Wall Studs at Corner Holes" in

the "Drill Holes in Rear Wall" section.

6. Check alignment of mounting plate, making sure it is level.

7. Securely tighten all lag screws and bolts.

Wall Stud at One Corner Hole (Figure 3)

1. With the support tabs of the mounting plate facing forward,

insert a 1/4-20 x 3" round-head bolt through the corner hole

that fits over the 3/4" (19 mm) hole drilled in Step 3 of

"Installation for One Wall Stud at One Corner Hole" in the "Drill

Holes in Rear Wall" section.

2. Start a toggle nut on the bolt from the back of the mounting

plate. Leave enough space for the toggle nut to go through

the wall and to open.

3. Position mounting plate on the wall, making sure that the top

of the mounting plate is aligned with the front edge of the

upper cabinet.

4. Push the bolt with toggle nut through the drywall, and finger

tighten the bolt to make sure toggle nut has opened against

drywall.

5. Insert a lag screw into the remaining bottom corner hole.

6. If installing on a second wall stud, insert a lag screw into the

other hole drilled in Step 2 of "Installation for One Wall Stud at

One Corner Hole" in the "Drill Holes in Rear Wall" section.

7. Check alignment of mounting plate, making sure it is level.

8. Securely tighten the lag screw(s) and bolt.

Wall Studs at Both Corner Holes (Figure 4)

1. Position mounting plate on the wall, making sure that the top

of the mounting plate is aligned with the front edge of the

upper cabinet.

2. Insert lag screws into both bottom corner holes.

3. Check alignment of mounting plate, making sure it is level.

4. Securely tighten the lag screws.

Prepare Upper Cabinet

1. Disconnect power to outlet.

2. Remove all contents from upper cabinet.

3. Place Upper Cabinet Template against the bottom of the

upper cabinet, and tape or tack it in place. Make sure the

template centerline aligns with the vertical centerline on the

rear wall.

The "rear wall" arrows must be against the rear wall so that the

holes cut into the upper cabinet align with the holes in the top

of the microwave oven.

NOTE: If the upper cabinet has a frame around it, trim the

template edges so that it fits inside the frame, against the upper

cabinet bottom. The template has trim lines to use as guides.

4. Make sure the 10 " (26.7 cm) dimension from the rear wall to

points "D" and "E" on the template is maintained.

(26.7 cm)

U p

p e r

- c a b i ne t t e m p l

a t

10 "

(26.7 cm)