Makita 6310 Інструкція з експлуатації - Сторінка 4
Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Дриль. Makita 6310. Makita 6310 12 сторінок. 2-speed drill
Друкувати сторінку
ENGLISH
1
Side grip
2
Tighten
3
Chuck key
4
Sleeve
5
Ring
6
Depth gauge
SPECIFICATIONS
Model
6310
Capacities
Steel ....................................................................................................... Hi: 8 mm
Wood ...................................................................................................... Hi: 20 mm
–1
No load speed (min
) ............................................................................... Hi: 0 – 2,000
Overall length ............................................................................................ 310 mm
Net weight ................................................................................................. 2 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to enclosed Safety
instructions.
SPECIFIC SAFETY RULES
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to drill safety rules. If you use this power tool
unsafely or incorrectly, you can suffer serious per-
sonal injury.
1.
Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
2.
Hold tool by insulated gripping surfaces when
performing an operation where the cutting tools
may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the opeator.
3.
Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
4.
Hold the tool firmly.
5.
Keep hands away from rotating parts.
6.
Do not leave the tool running. Operate the tool
only when hand-held.
7.
Do not touch the drill bit or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
8.
Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
SAVE THESE INSTRUCTIONS.
4
Explanation of general view
7
Screw
8
High
9
Low
10 Speed control screw
11 Switch trigger
12 Lock button
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
OPERATING INSTRUCTIONS
Installing side grip (auxiliary handle) (Fig. 1)
Screw the side grip on the tool securely.
Installing or removing drill bit
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the bit.
For tools with standard keyed chuck (Fig. 2)
To install the bit, place it in the chuck as far as it will go.
Tighten the chuck by hand. Place the chuck key in each
of the three holes and tighten clockwise. Be sure to
GEB001-2
tighten all three chuck holes evenly. To remove the bit,
turn the chuck key counterclockwise in just one hole,
then loosen the chuck by hand.
After using the chuck key, be sure to return it to the origi-
nal position.
For tools with keyless chuck (Fig. 3)
Hold the ring and turn the sleeve counterciockwise to
open the chuck jaws. Place the bit in the chuck as far as
it will go. Hold the ring firmly and turn the sleeve clock-
wise to tighten the chuck. To remove the bit, hold the ring
and turn the sleeve counterclockwise.
Adjusting depth of drilling (Fig. 4)
Loosen the screw and adjust the depth gauge to the
desired depth. After adjusting, tighten the screw.
13 Reversing switch lever
14 Speed change knob
–1
15 0 – 2,000 min
–1
16 0 – 700 min
17 Arrow
Low: 13 mm
Low: 32 mm
Low: 0 – 700