A&E Systems 8500 Інструкція із заміни Посібник із заміни

Переглянути онлайн або завантажити pdf Інструкція із заміни Посібник із заміни для Аксесуари A&E Systems 8500. A&E Systems 8500 6 сторінок. Sunchaser
Також для A&E Systems 8500: Посібник користувача (5 сторінок)

Друкувати сторінку

REPLA

REPLACEMENT INSTR

REPLA

Fabric

For Models 5000, 7000, 7500, 8000, 8500, 9000, 9500

Tools Required:

The Fabric Roller Tube Assembly (FRTA) consists of a

fabric, a roller tube and torsion assemblies.

For proper awning operation, the roller is under spring

tension from the torsion assemblies. Improper release of

this spring tension can result in damage to the aw-

ning, severe personal injury, or both.

B. B. B. B. B. REMO

NOTE:

NOTE: Awning removal from the coach is NOT neces-

sary when replacing a torsion assembly. Proceed to

Section C, Steps 1 & 2, Sections D, Steps 1-3, and

Section L, Steps 1-3.

1. In all instances of fabric or roller tube replacement, it

will be necessary to have a large work area to allow

complete unrolling of the awning. This work area must

be clean and smooth so the fabric will not be damaged.

2. Remove the TEK screws securing the awning fabric or

roller cover at each end of the awning rail. See FIG. 1.

3. Remove both top mounting brackets on the ends of the

awning rail. See FIG. 1

1/2" TEK

SCREW

FIG. 1

SECTION

CEMENT INSTR

CEMENT INSTRUCTIONS FOR A

CEMENT INSTR

Roller T T T T T ube

Roller

ube

Roller

ube

& Grande Pavilion

Vise Grips®

Socket Wrench Set

3/16" Drill Bit

1/8" Pop Rivets

A. GENERAL INSTRUCTIONS

Improper release of

REMO

REMOV V V V V AL OF

REMO

AL OF

AL OF THE A

AL OF

THE AWNING FR

THE A

REMOVE FROM

BOTH SIDES

AWNING

RAIL

FABRIC

TOP

BRACKET

UCTIONS FOR A

UCTIONS FOR AWNING

UCTIONS FOR A

T T T T T or or or or orsion Assemb

sion Assemb

sion Assembl l l l l y y y y y

sion Assemb

Screwdriver

Pop Rivet Tool

Electric Drill

Adjustable Wrench

Step Ladder

1/8" Drill Bit

3/16" Pop Rivets

Small File

Service to the FRTA should be performed

qualified service person.

Read and understand the instructions before starting the

replacement of a fabric, a roller tube or a torsion assembly.

WNING FR

WNING FROM

WNING FR

OM THE CO

THE CO

THE COA A A A A CH

4. Remove both of the patio feet from their mounting

brackets and extend the adjustable arms until each

patio foot rests on the ground and lock button locks in

hole.

5. Slide the awning fabric or roller cover out of the awning

rail.

a. To keep the 7500, 8000, 8500, 9000, 9500 and

Grande Pavilion Model Awnings from unwinding

during this step, be sure the cam lock lever is in the

roll down position. A 1/8" cotter pin can be inserted

in each torsion assembly for positive locking of the

roller tube. See FIG. 2.

MOVE LEVER POSITION TO

ROLL DOWN POSITION

FIG. 2

RIGHT-HAND SIDE

(VIEWED FROM FRONT)

WNING

ONLY

COTTER

AWNING

FABRIC

TOP CASTING

Form No. 3103699.033 11/93

(Replaces 3103699.025 10/92)

The Dometic Corp., LaGrange, IN 46761

by a