Garmin VIEO RV 1052 Посібник користувача - Сторінка 27
Переглянути онлайн або завантажити pdf Посібник користувача для Автомобільна навігаційна система Garmin VIEO RV 1052. Garmin VIEO RV 1052 38 сторінок.
Друкувати сторінку
Disabling a Zone
You can disable an unused zone and remove it from the audio
level pages. When a zone is disabled, you cannot change any of
the settings for that zone. You can disable zones 2, 3, and 4
only.
1
Select
>
>
>
2
Select a zone.
3
Select ZONE ENABLED to clear the check box.
Disabling the Internal Amplifiers
If you do not connect speakers directly to zones 1 and 2, you
can disable the internal amplifiers to reduce power consumption.
1
Select
>
>
>
2
Select INTERNAL AMP ON to clear the check box.
Network Configuration
TIP: You can select the network status icon from any screen to
open the network configuration menu.
Setting the Fusion PartyBus Device as the DHCP Server
If you connected two Fusion PartyBus devices together directly,
or connected more than two together using a network switch or
wireless access point and did not install a router, you must
configure only one Fusion PartyBus stereo to be the DHCP
server.
1
Select
>
>
>
ETHERNET IP > STATIC IP > SAVE.
2
Select
>
>
>
SERVER > DHCP ENABLED > SAVE.
You can configure the IP address range of the DHCP server
(DHCP Settings, page
21).
Setting the Fusion PartyBus Device as a Wireless Access
Point
Before you can connect additional Fusion PartyBus devices or
smartphones to a Fusion PartyBus device wirelessly, you must
configure at least one device as a wireless access point. This is
not necessary if you installed a wireless router or other wireless
access point on the network.
1
Select
>
>
>
POINT.
2
Select SSID, and change the default SSID, or name, for the
wireless access point (optional).
3
Select AP SECURITY, and change the security type for the
access point (optional).
NOTE: It is strongly recommended that you use the default
WPA2 PERSONAL AP SECURITY setting. It is the most
widely-used and secure wireless security protocol.
4
Select PASSWORD, and change the default password for
the access point (optional).
5
If necessary, select COUNTRY, and select your region.
6
Select CHANNEL, and select a channel range for the access
point (optional).
7
Select SAVE.
You can adjust the wireless access point configuration at any
time
(Wireless Access Point Settings, page
Connecting the Fusion PartyBus Device to a Wireless
Access Point
1
Select
>
>
>
SSID.
A list of wireless access points within rage appears.
2
Select the Fusion PartyBus wireless access point.
3
Select an option:
• To enter the password, select PASSWORD, enter the
password, and select
Music Playback
> ZONE.
> ZONE.
> NETWORK > ADVANCED >
> NETWORK > ADVANCED > DHCP
> NETWORK > WI-FI ACCESS
21).
> NETWORK > WI-FI CLIENT >
.
• If you are connecting to the wireless access point using
WPS, verify that WPS has been enabled on the access
point, and select WPS.
NOTE: It can take up to two minutes to successfully
connect to the access point after you select WPS.
4
Select SAVE.
Advanced Network Configuration
You can perform advanced networking tasks on a Fusion
PartyBus device, such as defining DHCP ranges and setting
static IP addresses.
Wireless Access Point Settings
Select
>
>
>
> NETWORK > ADVANCED > WI-FI
ACCESS POINT.
NOTE: You must configure the device to be a wireless access
point before you can change the settings
PartyBus Device as a Wireless Access Point, page
SSID: Sets the SSID, or name, for the network.
AP SECURITY: Sets the type of wireless security protocol used
by the access point.
NOTE: It is strongly recommended that you set the AP
SECURITY using WPA2 PERSONAL. It is the most widely-
used and secure wireless security protocol.
PASSWORD: Sets the password for the access point. This is
not available when the AP SECURITY setting is set to
NONE.
COUNTRY: Sets the region where the stereo is located.
Different regions may use different channels on the wireless
spectrum, so you should set this to best accommodate local
wireless devices.
CHANNEL: Sets the access point to use a group of channels in
the high, low, or middle range of the available spectrum for
your region. You may experience better performance if you
set the channel in a range with fewer broadcasting access
points.
DHCP SERVER: Sets the device to act as a wireless access
point and the DHCP server on the network
page
21).
WPS: Initiates a Wi‑Fi Protected Setup (WPS) connection.
Devices with a WPS button or setting can connect to the
access point on this stereo when the WPS connection is
active.
NOTE: It can take up to two minutes to successfully connect
to the access point after you select WPS.
DHCP Settings
Select
>
>
>
> NETWORK > ADVANCED > DHCP
SERVER.
DHCP ENABLED: Sets the device as the DHCP server on the
network.
START IP: Sets the first IP address in the IP-address range of
the DHCP server.
END IP: Sets the final IP address in the IP-address range of the
DHCP server.
Setting a Static IP Address
If the stereo is configured as a DHCP server, it is automatically
assigned the IP address of 192.168.0.1. You can change this IP
address.
If the stereo is a client on the network and you do not want the
DHCP server to automatically assign an IP address to the
stereo, you can set a static IP address.
NOTE: Every device on the network must have a unique IP
address. If you select a static IP address that is the same as the
IP address on the network, the devices will not work properly.
1
Select
>
>
>
IP > STATIC IP.
(Setting the Fusion
21).
(DHCP Settings,
> NETWORK > ADVANCED > WI-FI
21