Garmin echomap chirp 40 series Посібник користувача - Сторінка 17
Переглянути онлайн або завантажити pdf Посібник користувача для Морська система GPS Garmin echomap chirp 40 series. Garmin echomap chirp 40 series 34 сторінки.
Також для Garmin echomap chirp 40 series: Інструкція з монтажу Посібник з монтажу (6 сторінок)
Друкувати сторінку
1
Dock your vessel or drop the anchor.
2
Select Settings > Navigation > Auto Guidance > Shoreline
Distance > Normal.
3
Select a destination that you have navigated to previously.
4
Select Navigate To > Guide To.
5
Review the placement of the Auto Guidance line, and
determine whether the line safely avoids known obstacles
and the turns enable efficient travel.
6
Select an option:
• If the placement of the Auto Guidance line is satisfactory,
select MENU > Stop Navigation, and proceed to step 10.
• If the Auto Guidance line is too close to known obstacles,
select Settings > Navigation > Auto Guidance >
Shoreline Distance > Far.
• If the turns in the Auto Guidance line are too wide, select
Settings > Navigation > Auto Guidance > Shoreline
Distance > Near.
7
If you selected Near or Far in step 6, review the placement of
the Auto Guidance line, and determine whether the line
safely avoids known obstacles and the turns enable efficient
travel.
Auto Guidance maintains a wide clearance from obstacles in
open water, even if you set the Shoreline Distance setting to
Near or Nearest. As a result, the chartplotter may not
reposition the Auto Guidance line, unless the destination
selected requires navigation through a narrow waterway.
8
Select an option:
• If the placement of the Auto Guidance line is satisfactory,
select MENU > Stop Navigation, and proceed to step 10.
• If the Auto Guidance line is too close to known obstacles,
select Settings > Navigation > Auto Guidance >
Shoreline Distance > Farthest.
• If the turns in the Auto Guidance line are too wide, select
Settings > Navigation > Auto Guidance > Shoreline
Distance > Nearest.
9
If you selected Nearest or Farthest in step 8, review the
placement of the Auto Guidance line, and determine
whether the line safely avoids known obstacles and the turns
enable efficient travel.
Auto Guidance maintains a wide clearance from obstacles in
open water, even if you set the Shoreline Distance setting to
Near or Nearest. As a result, the chartplotter may not
reposition the Auto Guidance line, unless the destination
selected requires navigation through a narrow waterway.
10
Repeat steps 3 through 9 at least once more, using a
different destination each time, until you are familiar with the
functionality of the Shoreline Distance setting.
Auto Guidance Line Configurations
The Safe Depth and Safe Height settings influence how the
chartplotter calculates an Auto Guidance line. If an area has an
unknown water depth or an unknown obstacle height, the Auto
Guidance line is not calculated in that area. If an area at the
beginning or the end of an Auto Guidance line is shallower than
the safe water depth or lower than the safe obstacle height, the
Auto Guidance line is not calculated in that area. On the chart,
the course through those areas appears as a gray line. When
your boat enters one of those areas, a warning message
appears.
NOTE: Auto Guidance is available with premium charts, in some
areas.
You can set the parameters the chartplotter uses when
calculating an Auto Guidance line.
Navigation with a Chartplotter
CAUTION
Safe Depth: Sets the minimum depth (chart depth datum) the
chartplotter uses when calculating an Auto Guidance line.
NOTE: The minimum safe depth for the premium charts is 3
feet. If you enter a Safe Depth value of less than 3 feet, the
charts only use depths of 3 feet for Auto Guidance route
calculations.
Safe Height: Sets the minimum height (chart height datum) of a
bridge that your boat can safely travel under.
Shoreline Distance: Sets how close to the shore you want the
Auto Guidance line to be placed. The Auto Guidance line
may move if you change this setting while navigating. The
available values for this setting are relative, not absolute. To
ensure that the Auto Guidance line is placed the appropriate
distance from shore, you can assess the placement of the
Auto Guidance line using one or more familiar destinations
that require navigation through a narrow waterway
the Distance from Shore, page
Boundaries
Boundaries allow you to avoid or remain in designated areas in
a body of water. You can set an alarm to alert you when you
enter or exit a boundary.
You can create boundary areas, lines, and circles using the
map. You can also create boundary areas by converting saved
tracks or routes into boundary lines. You can create a boundary
area using waypoints by creating a route from the waypoints,
and converting the route into a boundary line.
You can select a boundary to act as the active boundary. Data
about the active boundary appears in the data fields on the
chart.
Creating a Boundary
1
Select User Data > Boundaries > New Boundary.
2
Select a boundary shape.
3
Follow the on-screen instructions.
Boundary Display Settings
Select User Data > Boundaries > Display Options.
Distance/Bearing: Allows you to hide or display the bearing and
distance to your destination for the active boundary.
Chart Display: Allows you to hide or display boundaries on the
chart.
Color: Sets the color of boundaries on the chart.
Converting a Route to a Boundary
Before you can convert a route to a boundary, you must create
and save at least one route
page
10).
1
Select User Data > Routes.
2
Select a route.
3
Select Edit Route > Save as Boundary.
Converting a Track to a Boundary
Before you can convert a track to a boundary, you must record
and save at least one track
1
Select User Data > Tracks.
2
Select a track.
3
Select Edit Track > Save as Boundary.
Editing a Boundary
1
Select User Data > Boundaries.
2
Select a boundary.
3
Select Edit Boundary.
4
Select an option:
• To edit the appearance of the boundary on the chart,
select Display Options.
(Adjusting
12).
(Creating and Saving a Route,
(Saving the Active Track, page
11).
13