Garmin GPSMAP 3005C Інструкція з монтажу Посібник з монтажу
Переглянути онлайн або завантажити pdf Інструкція з монтажу Посібник з монтажу для Морська система GPS Garmin GPSMAP 3005C. Garmin GPSMAP 3005C 10 сторінок. Declaration of conformity
Також для Garmin GPSMAP 3005C: Короткий довідник (2 сторінок), Посібник з шаблонів (1 сторінок), Короткий довідник (2 сторінок), Інструкція з монтажу Посібник з монтажу (17 сторінок), Декларація про відповідність (1 сторінок)
Друкувати сторінку
The GPSMAP 3000 series chartplotter and GPS antenna must be properly installed according to the following instructions. You need the
appropriate fasteners, tools, and mounts listed in each section. These items are available at most marine dealers. Always wear safety goggles,
ear protection, and a dust mask when drilling, cutting, or sanding. When drilling or cutting, always check what is on the opposite side of the
surface. Mount the GPSMAP 3000 series chartplotter in a location that provides a clear, glare-free view of the display and easy operation of the
controls or touch screen. If you experience difficulty installing the chartplotter, seek the assistance of a professional installer; or contact
Garmin
Product Support by phone at 913/397.8200 or 800/800.1020. Go to www.garmin.com/support. In Europe, contact Garmin
®
(Europe) Ltd. at 44/0870.8501241.
Before installing your GPSMAP 3000 series chartplotter, confirm that the package contains the items listed on the box. If any parts are missing,
contact your Garmin dealer immediately.
WARNING: See the Important Safety and Product Information guide in the product box for product warnings and other important
information.
To install the GPSMAP 3000 series chartplotter:
1. Mount the GPSMAP 3000 series chartplotter (Page 1).
2. Mount the GPS antenna (Page 3).
3. Connect the GPSMAP 3000 series device to power and to the GPS antenna (Page 6).
4. Ensure the chartplotter software is up-to-date (Page 10).
Although they are not necessary to use the GPSMAP 3000 chartplotter, you can also use this manual to:
•
Connect the chartplotter to NMEA 0183-compatible devices such as a VHF radio with DSC
•
Connect the chartplotter to an external alarm
•
Connect the chartplotter to a video input source
•
Connect the chartplotter to an external video monitor
•
Connect the chartplotter to other Garmin Marine Network compatible devices, such as a sounder or a radar
You can use the included bracket to bail mount the chartplotter, or you can use the included template and hardware to flush mount the
chartplotter.
Bail Mounting the GPSMAP 3000 Series Chartplotter
Use the included bracket to bail mount the GPSMAP 3000 series chartplotter.
Tools required (not included):
• Drill and drill bit
• Screwdriver
• Pencil
• Mounting hardware (screws or nuts, washers, and bolts)
NotE: The mounting hardware (screws or nuts, washers, and bolts) are not included. The holes on the bail mount are
Choose mounting hardware that fits the holes in the bail mount and securely attaches it to your specific mounting surface. The size of the drill bit
required depends on the mounting hardware chosen.
August, 2008
GPSMAP
3000 Series Installation Instructions
®
(Page
8).
(Page
Mounting the GPSMAP 3000 Series Chartplotter
8).
(Page
8).
190-00991-02 Rev. A
(Page
6).
(Page
9).
/
in. (7.9 mm) in diameter.
5
16
Printed in Taiwan