Garmin GPSMAP 5208 - Marine GPS Receiver Інструкція з монтажу Посібник з монтажу - Сторінка 3

Переглянути онлайн або завантажити pdf Інструкція з монтажу Посібник з монтажу для Морська система GPS Garmin GPSMAP 5208 - Marine GPS Receiver. Garmin GPSMAP 5208 - Marine GPS Receiver 25 сторінок. Weather and xm satellite radio gpsmap 4000 series; gpsmap 5000 series; gpsmap 6000 series; gpsmap 7000 series
Також для Garmin GPSMAP 5208 - Marine GPS Receiver: Важлива інформація про безпеку (4 сторінок), Короткий довідник (2 сторінок), Посібник користувача (2 сторінок), Посібник користувача (2 сторінок), Технічна довідка (30 сторінок), Інструкція з монтажу Посібник з монтажу (19 сторінок), Короткий довідник (2 сторінок), Інструкція з монтажу Посібник з монтажу (25 сторінок), Декларація про відповідність (1 сторінок), Посібник з друку (2 сторінок), Посібник з доповнення (24 сторінок), Посібник користувача (6 сторінок)

To flush mount a GPSMAP 4008/4208/4012/4212 chartplotter or a GPSMAP 5008/5208/5012/5212 chartplotter:

1. The flush-mount template is included in the product box. Trim the template and ensure it will fit in the location at which you want to flush

mount the chartplotter.

NotE: Make sure the surface on which you mount the chartplotter has at least 7 in. (18 cm) of open space behind it to fit the chartplotter and the

connected wires.

NotE: Make sure to leave approximately

NotE: Mount a 4008/4208/5008/5208 chartplotter 31

to avoid interference.

2. The flush-mount template has adhesive on the back. Remove the protective liner and apply the template to the location at which you want to

mount the chartplotter.

3. Using a

in. (10 mm) drill bit, drill one or more of the four pilot holes inside the corner of the template to begin cutting the mounting surface.

4. Using the jigsaw, cut the mounting surface along the inside of the solid line indicated on the flush-mount template. Use a file and sandpaper

to refine the size of the hole. Be very careful when cutting this hole. There is only a small amount of clearance between the case and

the mounting holes.

5. Install the four mounting studs into the chartplotter by screwing the shorter, threaded section into the back of the chartplotter. Use the

(2 mm) Allen wrench to tighten the mounting studs until they stop. Do not overtighten - you may damage the mounting stud or the

mounting holes. The studs are coated with a reusable thread-locking patch applied at the factory.

6. Place the chartplotter in the hole and make sure that the mounting studs line up with the pilot holes on the flush-mount template after cutting,

sanding, and filing the hole. If they do not, mark the locations where the studs will feed through the mounting surface.

7. Using the center punch, indent the center of each of the 4 mm mounting-hole locations.

8. Using a 4 mm drill bit, drill the four mounting holes.

9. Install the rubber gasket on the back of the chartplotter. The top and bottom sections will line up with the holes. The side sections will line up

with the notches in the case (for the cover)

10. P lace the chartplotter into the cutout. The four mounting studs should feed through the four mounting holes drilled in step 8.

11. P lace the flat washers and the lock washers over the mounting studs. Then thread the hex nuts onto the mounting studs. Tighten all four hex

nuts evenly until the chartplotter is snug against the mounting surface.

Flush Mounting a GPSMAP 4008/4208/4012/4212/5008/5208/5012/5212 Chartplotter

GPSMAP 4000/5000 Series Installation Instructions

in. (13 mm) of space on the right side of the chartplotter to access the SD card door.

in. (80 cm), and a 4012/4212/5012/5212 chartplotter 39

Chartplotter

Mounting studs ×4

Rubber gasket

Mounting surface

Lock washers ×4

Flat washers ×4

Hex nuts ×4

in. (1 m) from a magnetic compass

in.