Garmin GPSMAP 7X2 PLUS Інструкція з монтажу Посібник з монтажу - Сторінка 4

Переглянути онлайн або завантажити pdf Інструкція з монтажу Посібник з монтажу для Морська система GPS Garmin GPSMAP 7X2 PLUS. Garmin GPSMAP 7X2 PLUS 8 сторінок.

Друкувати сторінку
This device can connect to a NMEA 2000 network on your boat
to share data from NMEA 2000 compatible devices such as a
GPS antenna or a VHF radio. The included NMEA 2000 cables
and connectors allow you to connect the device to your existing
NMEA 2000 network. If you do not have an existing NMEA 2000
network you can create a basic one using cables from Garmin.
If you are unfamiliar with NMEA 2000, you should read the
Technical Reference for NMEA 2000 Products at
/manuals/nmea_2000.
The port labeled NMEA 2000 is used to connect the device to a
standard NMEA 2000 network.
Item
Description
NMEA 2000 compatible Garmin device
GPS antenna
Ignition or in-line switch
NMEA 2000 power cable
NMEA 2000 drop cable
12 Vdc power source
NMEA 2000 terminator or backbone cable
NMEA 2000 T-connector
NMEA 2000 terminator or backbone cable

NMEA 0183 Connection Considerations

• The chartplotter provides one Tx (transmit) port and one Rx
(receive) port.
• Each port has 2 wires, labeled A and B according to the
NMEA 0183 convention. The corresponding A and B wires of
each internal port should be connected to the A (+) and B (-)
wires of the NMEA 0183 device.
• You can connect one NMEA 0183 device to the Rx port to
input data to this chartplotter, and you can connect up to
three NMEA 0183 devices in parallel to the Tx port to receive
data output by this chartplotter.
• See the NMEA 0183 device installation instructions to identify
the transmit (Tx) and receive (Rx) wires.
• You must use 28 AWG, shielded, twisted-pair wiring for
extended runs of wire. Solder all connections and seal them
with heat-shrink tubing.
• Do not connect the NMEA 0183 data wires from this device
to power ground.
• The power cable from the chartplotter and the NMEA 0183
devices must be connected to a common power ground.
• The internal NMEA 0183 ports and communication protocols
are configured on the chartplotter. See the NMEA 0183
section of the chartplotter owner's manual for more
information.
4
• See the chartplotter owner's manual for a list of the approved
NMEA 0183 sentences that the chartplotter supports.
NMEA 0183 Device Connections
This diagram illustrates two-way connections for both sending
and receiving data. You can also use this diagram for one-way
communication. To receive information from a NMEA 0183
device, refer to items
garmin.com
Garmin device. To transmit information to a NMEA 0183 device,
refer to items
device.
Item
Item Garmin Wire Function Garmin Wire
Power
Power ground
Data ground
Rx/A (In +)
Rx/B (In -)
Tx/A (Out +)
Tx/B (Out -)
If the NMEA 0183 device has only one input (receive, Rx) wire
(no A, B, +, or -), you must leave the gray wire unconnected.
If the NMEA 0183 device has only one output (transmit, Tx) wire
(no A, B, +, or -), you must connect the violet wire to ground.
NMEA 0183 and Power Cable Pinout
Pin Number
,
,
,
, and
,
,
,
, and
when connecting the Garmin
Description
Power source
Power/NMEA 0183 cable
NMEA 0183 device
Color
Red
Black
Black
Brown
Violet
Blue
Gray
Wire Function
NMEA 0183 Tx/A (Out
+)
NMEA 0183 Rx/A (In
+)
NMEA 0183 Tx/B (Out
-)
NMEA 0183 Rx/B (In
-)
Alarm
Accessory on
when connecting the
NMEA 0183 Device
Wire Function
Power
Power ground
Data ground
Tx/A (Out +)
Tx/B (Out -)
Rx/A (In +)
Rx/B (In -)
Wire Color
Blue
Brown
Gray
Violet
Yellow
Orange