Garmin GPSMAP 8000 Series Посібник користувача - Сторінка 26

Переглянути онлайн або завантажити pdf Посібник користувача для Морська система GPS Garmin GPSMAP 8000 Series. Garmin GPSMAP 8000 Series 43 сторінки. Installation instructions
Також для Garmin GPSMAP 8000 Series: Посібник користувача (36 сторінок), Посібник із швидкого старту (4 сторінок), Інструкція з експлуатації (15 сторінок), Інструкція з монтажу Посібник з монтажу (14 сторінок)

Garmin GPSMAP 8000 Series Посібник користувача
Orientation: Sets the perspective of the radar display. The
orientation setting applies to every radar mode. This setting
does not apply to the Radar overlay.
Appearance: Sets the color scheme, look-ahead speed, and
navigation appearance.
Front of Boat: Compensates for the physical location of the
radar scanner on a boat, if the radar scanner does not align
with the bow-stern axis.
Radar Appearance Settings
From a Radar screen, select Menu > Radar Setup >
Appearance.
NOTE: These settings do not apply to the Radar overlay.
Color Scheme: Sets the color scheme.
Look-Ahead Speed: Shifts your present location toward the
bottom of the screen automatically as your speed increases.
Enter your top speed for the best results.
Heading Line: Shows an extension from the bow of the boat in
the direction of travel on the radar screen.
Rings: Shows the range rings that help you to visualize
distances on the radar screen.
Nav Lines: Shows the navigation lines that indicate the course
you have set using Route To, Guide To, or Go To.
Waypoints: Shows waypoints on the radar screen.
Front-of-Boat Offset
The front-of-boat offset compensates for the physical location of
the radar scanner on a boat, if the radar scanner does not align
with the bow-stern axis.
Measuring the Potential Front-of-Boat Offset
The front-of-boat offset compensates for the physical location of
the radar scanner on a boat, if the radar scanner does not align
with the bow-stern axis.
1
Using a magnetic compass, take an optical bearing of a
stationary target located within viewable range.
2
Measure the target bearing on the radar.
3
If the bearing deviation is more than +/- 1°, set the front-of-
boat offset.
Setting the Front-of-Boat Offset
Before you can set the front-of-boat offset, you must measure
the potential front-of-boat offset.
The front-of-boat offset setting configured for use in one radar
mode is applied to every other radar mode and to the Radar
overlay.
1
From a Radar screen or the Radar overlay, select Menu >
Radar Setup > Front of Boat.
2
Select Up or Down to adjust the offset.

Selecting a Different Radar Source

1
Select an option:
• From a radar screen or the radar overlay, select Menu >
Radar Setup > Source.
• Select Settings > Communications > Preferred
Sources > Radar.
2
Select the radar source.
Autopilot
You can use the autopilot feature only at a station installed next
to a helm, throttle, and helm control device.
You are responsible for the safe and prudent operation of your
vessel. The autopilot is a tool that enhances your capability to
operate your boat. It does not relieve you of the responsibility of
Autopilot
WARNING
safely operating your boat. Avoid navigational hazards and
never leave the helm unattended.
Always be prepared to promptly regain manual control of your
boat.
Learn to operate the autopilot on calm and hazard-free open
water.
Use caution when operating the autopilot near hazards in the
water, such as docks, pilings, and other boats.
The autopilot system continuously adjusts the steering of your
boat to maintain a constant heading (heading hold). The system
also allows manual steering and several modes of automatic-
steering functions and patterns.

Opening the Autopilot Screen

Before you can open the autopilot screen, you must have a
compatible autopilot installed and configured.
Select A/V, Gauges, Controls > Autopilot.
Autopilot Screen
Actual heading
Intended heading (heading the autopilot is steering toward)
Actual heading (when in standby mode)
Intended heading (when engaged)
Rudder position indicator (This functionality is available only when a
rudder sensor is connected.)
Adjusting the Step Steering Increment
1
From the Autopilot screen, select Menu > Autopilot Setup >
Steering Mode > Step Turn Size.
2
Select an increment.
Setting the Power Saver
You can adjust the level of rudder activity.
1
From the autopilot screen, select Menu > Autopilot Setup >
Power Saver.
2
Select a percentage.
Selecting a higher percentage reduces rudder activity at the
expense of heading performance. The higher the percentage,
the more the course deviates before the autopilot corrects it.
TIP: In choppy conditions at low speeds, increasing the
Power Saver percentage reduces rudder activity.
Enabling Shadow Drive
NOTE: The Shadow Drive feature is available only on hydraulic
steering systems.
From the autopilot screen, select Menu > Autopilot Setup >
Shadow Drive > Enabled.

Engaging the Autopilot

When you engage the autopilot, the autopilot takes control of the
helm and steers the boat to maintain your heading.
From any screen, select Engage.
25