Garmin ECHOMAP UHD Інструкція з монтажу Посібник з монтажу - Сторінка 4

Переглянути онлайн або завантажити pdf Інструкція з монтажу Посібник з монтажу для Морське обладнання Garmin ECHOMAP UHD. Garmin ECHOMAP UHD 6 сторінок.

Друкувати сторінку

damage caused by fire or overheating, the appropriate fuse

must be in place as indicated in the product specifications. In

addition, connecting the power cable without the appropriate

fuse in place voids the product warranty.

You should connect the red wire to the same battery through the

ignition or another manual switch to turn the device on and off.

Route the power cable between the power source and the

device.

Connect the red power wire to the ignition or another manual

switch, and connect the switch to the positive (+) battery

terminal if necessary.

Connect the black wire to the negative (-) battery terminal or

to ground.

Connect the power cable to the device, and turn the locking

ring clockwise to tighten it.

Connecting the Device to a Transducer

Go to

garmin.com/transducers

dealer to determine the appropriate type of transducer for your

needs.

Follow the instructions provided with your transducer to

correctly install it on your boat.

Route the transducer cable to the back of your device, away

from sources of electrical interference.

Connect the transducer cable to the appropriate port on the

cradle.

Connecting to a Garmin Device to Share User Data

NOTE: This feature is not available on ECHOMAP UHD 7x/9x

devices. The blue and brown wires on those devices can

connect to NMEA 0183 devices only.

You can connect the ECHOMAP UHD 6x device to a compatible

Garmin device to share user data, such as waypoints. If the

devices are mounted near each other, you can connect the blue

and brown wires. If the devices are mounted too far apart for the

wires to reach, you can connect the devices using a User Data

Sharing Cable (010-12234-06).

Make sure both devices are connected to the same ground.

Complete an action:

• If the devices are mounted near each other, connect the

blue wire from the first device to the brown wire of the

second, and connect the brown wire from the first device

to the blue wire of the second.

• If the devices are not mounted near each other, obtain a

User Data Sharing Cable (010-12234-06), and connect

the devices following the instructions included with the

cable.

On both devices, select Nav Info > Manage Data > User

Data Sharing.

User data is shared between the connected devices. If you

select Clear User Data, data is removed from both connected

devices.

Installing the Ferrite Bead on the Transducer Cable

To comply with regulations and to reduce noise, you should

install the ferrite bead on the transducer cable, if a ferrite bead is

included.

Securely snap the ferrite bead around the transducer cable,

as close to the connector as possible.

or contact your local Garmin

NMEA 2000 Considerations

If you are connecting to an existing NMEA 2000 network,

identify the NMEA 2000 power cable. Only one NMEA 2000

power cable is required for the NMEA 2000 network to operate

properly.

A NMEA 2000 Power Isolator (010-11580-00) should be used in

installations where the existing NMEA 2000 network

manufacturer is unknown.

If you are installing a NMEA 2000 power cable, you must

connect it to the boat ignition switch or through another in-line

switch. NMEA 2000 devices will drain your battery if the NMEA

2000 power cable is connected to the battery directly.

You can connect your device to a NMEA 2000 network on your

boat to share data from NMEA 2000 compatible devices such as

sensors or a VHF radio. The necessary NMEA 2000 cables and

connectors are sold separately.

If you are unfamiliar with NMEA 2000, you should read the

"NMEA 2000 Network Fundamentals" chapter of the Technical

Reference for NMEA 2000 Products. You can find this document

using the "Manuals" link on the product page for your device at

garmin.com.

The port labeled NMEA 2000 on the cradle is used to connect it

to a standard NMEA 2000 network.

Item

Description

ECHOMAP UHD device

NMEA 2000 drop cable

NMEA 2000 power cable

Ignition or in-line switch

12 Vdc power source

NMEA 2000 terminator or backbone cable

NMEA 2000 T-connector

NMEA 2000 terminator or backbone cable

Installing the Device in the Cradle

After the cables are connected to the cradle, you can quickly

place the device in the cradle.

Place the base of the device in the bottom of the cradle.

Tilt the top of the device toward the cradle until it fastens in

place.

There is an audible click when the device is secured in the

cradle.

NOTICE