Garmin GHP 10 Інструкція з монтажу Посібник з монтажу - Сторінка 39
Переглянути онлайн або завантажити pdf Інструкція з монтажу Посібник з монтажу для Морське обладнання Garmin GHP 10. Garmin GHP 10 48 сторінок. Autopilot system, addendum
Також для Garmin GHP 10: Інструкція з монтажу Посібник з монтажу (26 сторінок), Посібник користувача (28 сторінок), Декларація про відповідність (1 сторінок), Посилання (1 сторінок), Примітки до конфігурації (14 сторінок)
Друкувати сторінку
Category
Tachometer Setup
Tachometer Setup
Tachometer Setup
Tachometer Setup
Tachometer Setup
Hydraulic Setup
Hydraulic Setup
Hydraulic Setup
Hydraulic Setup
Turn Fine Tuning Setup > Rudder Gains
Turn Fine Tuning Setup > Rudder Gains
Turn Fine Tuning Setup > Rudder Gains
Turn Fine Tuning Setup > Rudder Gains
Turn Fine Tuning Setup
Navigation Setup
Navigation Setup > NMEA Setup
Navigation Setup > NMEA Setup
Navigation Setup
Navigation Setup
note: Certain configuration settings are available when using the GHC 10 normally, such as enabling and disabling the Shadow
Drive, adjusting the sensitivity of the Shadow Drive, and adjusting the Sea State Filtering setting. See the configuration section of the
GHP 10/GHC 10 Quick Start Manual for more information.
GHP 10 Marine Autopilot System Installation Instructions
Setting
Description
Verify Tachometer
With the engine (or engines) running, compare the RPM readings on the
GHC 10 with the tachometer on the dashboard of your boat. Adjust the
Pulses Per Rev
select Done. When you adjust the
is a delay before the new RPM readings appear on the GHC 10. For each
adjustment, be sure to wait until the GHC 10 adjusts to the new reading.
RPM Source
Select the engine (or engines) to which you wired the tachometer sensor
from the CCU. If you connected a NMEA 2000-compatible engine to the
NMEA 2000 network, select
port.
Planing RPM
Take note of the RPM reading from the tachometer on the dashboard of
your boat at the point your boat transitions from displacement to planing
speed. If the value does not match the value on the GHC 10, use the
arrows to adjust the value.
Low RPM Limit
Take note of the RPM reading from the tachometer on the dashboard of
your boat at the lowest RPM point. If the value does not match the value
on the GHC 10, use the arrows to adjust the value.
High RPM Limit
Take note of the RPM reading from the tachometer on the dashboard of
your boat at the highest RPM point. If the value does not match the value
on the GHC 10, use the arrows to adjust the value.
Helm Displacement
The helm displacement is usually written on the body of the helm pump.
If you are unsure, consult the manufacturer of your boat for the helm
displacement value. Use the arrows on the GHC 10 to enter the helm
displacement value.
Lock to Lock Turns
Count the number of turns it takes your helm to go from lock to lock (fully
turned port to fully turned starboard). Use the arrows on the GHC 10 to
enter the value you counted.
Verify Steering Direction
Use the arrows on the GHC 10 to test the steering direction. When you
push the right arrow, the motor should turn the boat to the right, and vice
versa. Determine if the engines are steering in the correct direction and
press Continue. Use the GHC 10 to answer the questions.
Linkage Compensation
Adjust the linkage compensation if the steering is loose or sloppy. The
higher you set this value, the more the autopilot compensates for loose or
sloppy steering. Use this setting with caution.
Low Speed
Set the rudder gain for low speeds.
Low Speed Counter
Set the rudder gain counter-correction for low speeds.
High Speed
Set the rudder gain for high speeds.
High Speed Counter
Set the rudder gain counter-correction for high speeds.
Acceleration Limiter
Limit the aggressiveness of autopilot-controlled turns. Increase the
percentage to limit the turn rate, and decrease the percentage to allow
higher turn rates.
Fine Heading Adjustment
Increase or decrease to fine-tune the autopilot heading.
NMEA Checksum
If the connected GPS unit incorrectly calculates checksums, you may
still be able to use it if you turn this setting off. When off, data integrity is
compromised.
Reversed XTE
If the connected GPS unit sends the incorrect steering direction with the
cross track error signal, use this setting to correct the steering direction.
Navigation Gain
Because the cross track error data transmitted by a NMEA 0183 GPS
device is only accurate within .01 mile (60 ft.), the gain may need
adjustment. Increase this setting until the boat oscillates back and forth
near the course line, then lower it a few levels.
Navigation Trim Gain
After adjusting the Navigation gain, increase this setting until you can see
the standoff from the course line decreasing over time.
with the arrows if the values do not match, and then
Pulses Per Rev
nMEA
2000. For a single-engine boat, select
with the arrows, there
9