Garmin Delta Upland XC Handheld Інструкція з експлуатації - Сторінка 2
Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Засіб для догляду за домашніми тваринами Garmin Delta Upland XC Handheld. Garmin Delta Upland XC Handheld 6 сторінок.
Друкувати сторінку
Beeper Instructions
Beeper Device Overview
Battery cover
Power key
Speaker
Status LEDs
Putting the Beeper Device on Your Dog
You should install the beeper device onto the same collar strap
with a compatible dog device, such as a Delta Upland™ device
or a Garmin Pro series device.
1
Insert the end of the collar strap through the slot at the base
of the beeper device.
2
Place the collar on the dog's neck, and position the beeper
device at the back of the dog's neck.
Beeper Sounds
The beeper device can emit two sounds: a beep and a hawk scream. These sounds indicate your dog's hunting and pointing status.
While your dog is hunting, the beeper device emits a series of one to three beeps every four seconds. You can select the number of
beeps in the series, which is useful to distinguish between multiple dogs. You can also disable this sound so that the beeper device
is silent while your dog is hunting.
When your dog is pointing, the beeper emits either one beep every second or one hawk scream every five seconds, depending on
the setting you choose.
When you select beeper sounds, the selected sounds are indicated briefly by the status LEDs. The red status LED indicates the
hunting sound, and the green status LED indicates the pointing sound.
Mode Red LED Hunting Sound Green LED Pointing Sound
1
1 blink
1 beep
2
2 blinks
2 beeps
3
3 blinks
3 beeps
4
Off
Silent
5
1 blink
1 beep
6
2 blinks
2 beeps
7
3 blinks
3 beeps
8
Off
Silent
Customizing the Beeper Sounds
1
With the device turned on, hold the power key until both
LEDs blink rapidly three times, and release the power key.
2
Select the power key to cycle through the sound modes.
Each time you select the power key, the LEDs indicate the
selected sound mode. You may have to cycle through
several sound modes to reach your preferred sound mode.
3
Hold the power key until both LEDs blink rapidly three times,
and release the power key to set the sound mode to the
current selection.
Resetting to the Default Beeper Sounds
You can reset your beeper device to the factory default sound
settings, regardless of the current setting or power state of the
device.
Hold the power key for 15 seconds.
The device emits a high-low, high-low beep sequence, and
the LEDs flash to confirm the reset.
The next time you turn on the device, it is set to mode 1.
2
Solid
Hawk scream
Blinking
Beep
Turning the Beeper Device On and Off
• Hold the power key until the red status LED flashes once to
turn on the device.
• Hold the power key until red status LED turns off, and then
release the power key immediately to turn off the device.
Turning the Beeper Sounds On or Off Remotely
Before you can turn the beeper sounds on or off remotely, the
dog collar device and the beeper device must be turned on.
You can use the handheld device to turn the beeper sounds on
or off remotely. Turning off the beeper sounds does not turn off
the beeper device.
1
On the handheld device, select a training mode in which a
training key is assigned to the beeper device.
2
Select the training key assigned to the beeper device to turn
the beeper sounds on or off for the selected dog.
Replacing the Beeper Battery
Before you can replace the battery, you must have a Phillips-
head screwdriver and a CR123A lithium battery.
1
Using a Phillips-head screwdriver, remove the screw
the battery cover
.
from