Fujitsu ABT series Посібник з експлуатації - Сторінка 8
Переглянути онлайн або завантажити pdf Посібник з експлуатації для Кондиціонер Fujitsu ABT series. Fujitsu ABT series 20 сторінок. Floor console/under ceiling dual type
Також для Fujitsu ABT series: Посібник з експлуатації (18 сторінок), Посібник з експлуатації (20 сторінок), Посібник з експлуатації (20 сторінок)
Друкувати сторінку
TIMER OPERATION
Before using the timer function, be sure that the Remote Control Unit is set to the correct current time ( P. 4).
If the indoor unit is connected to a wired remote controller, the wireless remote controller cannot be used to set the timer.
To Use the ON timer or OFF timer
1
Press the START/STOP button
(if the unit is already operating, proceed to step 2).
The indoor unit's OPERATION Indicator Lamp (green) will light.
2
Press the TIMER MODE button to select the OFF timer
or ON timer operation.
Each time the button is pressed the timer function changes in the follow-
ing order:
s
PROGRAM (OFF → ON, OFF ← ON)
The indoor unit's orange TIMER Indicator Lamp (orange) will light.
3
Use the TIMER SET buttons to adjust the desired OFF
time or ON time.
Set the time while the time display is flashing (the flashing will continue
for about five seconds).
button: Press to advance the time.
button: Press to reverse the time.
About five seconds later, the entire display will reappear.
To Use the Program timer
1
Press the START/STOP button
(if the unit is already operating, proceed to step 2).
The indoor unit's OPERATION Indicator Lamp (green) will light.
2
Set the desired times for OFF timer and ON timer.
See the section "To Use the ON timer or OFF timer" to set the desired
mode and times.
About three seconds later, the entire display will reappear.
The indoor unit's TIMER Indicator Lamp (orange) will light.
3
Press the TIMER MODE button to select the PROGRAM
timer operation (OFF
The display will alternately show "OFF timer" and "ON timer", then change
to show the time setting for the operation to occur first.
G
The program timer will begin operation. (If the ON timer has been se-
lected to operate first, the unit will stop operating at this point.)
About five seconds later, the entire display will reappear.
About the Program timer
G
The program timer allows you to integrate OFF timer and ON timer operations in
a single sequence. The sequence can involve one transition from OFF timer to
ON timer, or from ON timer to OFF timer, within a twenty-four hour period.
G
The first timer function to operate will be the one set nearest to the current time.
The order of operation is indicated by the arrow in the Remote Control Unit's
Display (OFF → ON, or OFF ← ON).
G
One example of Program timer use might be to have the air conditioner auto-
matically stop (OFF timer) after you go to sleep, then start (ON timer) automati-
cally in the morning before you arise.
7
CANCEL
s
OFF
s
ON or OFF
ON
t
ON will display).
To Cancel the Timer
Use the TIMER MODE button to select
"CANCEL".
The air conditioner will return to normal
operation.
To Change the Timer Settings
Perform steps 2 and 3.
To Stop Air Conditioner Operation
while the Timer is Operating
Press the START/STOP button.
To Change Operating Conditions
If you wish to change operating conditions
(Mode, Fan Speed, Thermostat Setting,
QUIET mode), after making the timer setting
wait until the entire display reappears, then
press the appropriate buttons to change the
operating condition desired.
To Cancel the Timer
Use the TIMER MODE button to select
"CANCEL".
The air conditioner will return to normal
operation.
To Change the Timer Settings
1. Follow the instructions given in the section
"To Use the ON Timer or OFF Timer" to
select the timer setting you wish to change.
2. Press the TIMER MODE button to select
either OFF
ON or OFF
To Stop Air Conditioner Operation
while the Timer is Operating
Press the START/STOP button.
To Change Operating Conditions
If you wish to change operating conditions
(Mode, Fan Speed, Thermostat Setting,
QUIET mode), after making the timer setting
wait until the entire display reappears, then
press the appropriate buttons to change the
operating condition desired.
ON.