Fujitsu RSG36KMTA Посібник з експлуатації - Сторінка 6
Переглянути онлайн або завантажити pdf Посібник з експлуатації для Кондиціонер Fujitsu RSG36KMTA. Fujitsu RSG36KMTA 16 сторінок.
Друкувати сторінку
3.3. Inserting batteries
Battery type: R03/LR03/AAA x 2
1
2
9
5
1
Pull the cover in the direction of the arrow and open it
until it is trapped.
2
Remove the cover.
① Turn the remote controller over and push the back
side of the cover and remove the claws by curving
the cover.
② Pull in the direction of the arrow while curving the
cover.
3
Put batteries as shown in the figure above.
4
Press this button as shown in the figure above.
Use the tip of a ballpoint pen or other small objects.
5
Press
to start setting day of the week and clock.
(
6
Press
Sunday).
7
Press
to continue.
(
8
Press
Press the buttons to change the clock by a minute.
Press and hold the buttons to change the clock by 10 minutes.
* By pressing
from a 24-hour to a 12-hour clock.
9
Press
to complete the setting.
Be close to the indoor unit. If you press the button from a
distance, settings may not be properly sent.
10
Install and close the cover.
NOTES:
• Use specified type of batteries only.
• Do not mix different types or new and used batteries together.
• Batteries can be used about 1 year in ordinary use.
• If the remote control range noticeably shortens, replace the
batteries, and press
4. BASIC OPERATIONS
■ 3 steps to start operation
1. Press
to start or stop the operation.
2. Press
to select the operation mode.
The operation mode changes as follows.
AUTO
COOL
3. Press
to set the desired temperature.
The temperature changes by 0.5 °C increments.
Temperature setting range
Auto/Cooling/Dry
Heating
En-5
3
7
6
RESET
8
4
)
to set day of the week (Monday to
)
to set the clock.
, the time indicator can be changed
as shown in the figure above.
DRY
FAN
HEAT
18.0 - 30.0 °C
16.0 - 30.0 °C
NOTES:
• In the Cooling or Dry mode,
- set the temperature lower than the current room temperature.
- the indoor unit fan may stop from time to time to perform Fan
control for energy saving that enables power-saving operation by
stopping the rotation of the indoor unit fan when the outdoor unit is
stopped.
In initial setting, this function is activated.
To deactivate the function, refer to "7.3. Fan control for energy
saving".
• In the Heating mode,
- set the temperature higher than the current room temperature.
- at the beginning of the operation, the indoor unit fan rotates at very
low speed for 3-5 minutes.
- the Automatic defrosting operation overrides the Heating operation
when necessary.
• In the Fan mode, temperature control is not available.
■ Temperature unit switching
1. Press
until only the clock is displayed.
2. Press and hold
The current temperature unit will be displayed. (Factory setting: °C)
to switch the temperature unit. (°C ⇔ °F)
3. Press
4. Press
to finish the setting.
If you do not press the button for 30 seconds, the displayed
temperature unit will be set.
5. AIRFLOW SETTINGS
5.1. Fan speed setting
Press
to control the fan speed.
)
)
The fan speed changes as follows.
(Auto)
(High)
When
is selected, the fan speed depends on the operating
condition.
To increase the air cleaning effect, set the fan speed to High.
5.2. Airflow direction setting
For details of the airflow ranges, refer to "Airflow direction
range".
■ Up/down airflow direction setting
Press
to adjust the up/down airflow direction.
)
)
■ Left/right airflow direction setting
Press
to adjust the left/right airflow direction.
)
)
■ Swing operation setting
Press
to select the Swing operation.
)
)
The Swing operation changes as follows.
Up/down
Left/right
NOTE: The Swing operation may stop temporarily when the indoor unit
fan is rotating at very low speed or is stopped.
■ Airflow direction range
Up/down airflow direction
Change by
Cooling, Dry
Heating, Fan
1
Swing operation by
2
3
Cooling, Dry
4
Heating
5
6
Fan *
* The Swing operation range depends on the airflow direction set before
the Swing operation.
for more than 5 seconds.
(Med)
(Low)
(Quiet)
Up/down/left/right
Stop swing
1 ⇄ 2 ⇄ 3 ( ⇄ 4 ⇄ 5 ⇄ 6)
1 ⇄ 2 ⇄ 3 ⇄ 4 ⇄ 5 ⇄ 6
1
4
3
6
1
4 or 3
6