Fujitsu Lifebook B3010D Посібник з біосу - Сторінка 2
Переглянути онлайн або завантажити pdf Посібник з біосу для Ноутбук Fujitsu Lifebook B3010D. Fujitsu Lifebook B3010D 28 сторінок. Lifebook b series
Також для Fujitsu Lifebook B3010D: Посібник з біосу (38 сторінок)
Друкувати сторінку
L i f e B o o k B S e r i e s N o t e b o o k B I O S
B Series BIOS
BIOS SETUP UTILITY
The BIOS Setup Utility is a program that sets up the
operating environment for your notebook. Your BIOS
is set at the factory for normal operating conditions,
therefore there is normally no need to set or change the
BIOS environment to operate your notebook.
The BIOS Setup Utility configures:
• Device control feature parameters, such as changing
I/O addresses and boot devices.
• System Data Security feature parameters, such
as passwords.
Entering the BIOS Setup Utility
To enter the BIOS Setup Utility do the following:
1. Turn on or restart your notebook.
2. Press the [
] key once the Fujitsu logo appears
F2
on the screen. This will open the main menu
of the BIOS Setup Utility with the current
settings displayed.
3. Press the arrow keys to scroll through the other
setup menus to review or alter the current settings.
Navigating Through The Setup Utility
The BIOS setup utility consists of six menus; Main,
Advanced, Security, Boot, Info and Exit. This document
explains each menu, including all submenus and setup
items.
The following procedures allow you to navigate the setup
utility menus:
1. To select a menu, use the cursor keys: [
2. To select a field within a menu or a submenu, use the
cursor keys: [ ], [
3. To select the different values for each field, press the
[
] or [
] to change to the next higher selec-
Spacebar
+
tion and [
] or [-] to go to the next lower selection.
F5
4. To activate a submenu press the [Enter] key.
5. To return to a menu from a submenu, press
the [
] key.
Esc
6. To go to the Exit menu from any other menu,
press the [
] key.
Esc
2
],[
].
• Selecting a field causes a help message
• Pressing the Enter key with the highlight
7. Pressing the [
the default values.
8. Pressing the [
tion and exits the BIOS Setup Utility. You will be
asked to verify this selection before it is executed.
9. Pressing the [
Entering the Setup Utility After a Configuration
Change or System Failure
If there has been a change in the system configuration
that does not match the parameter settings stored
in your BIOS memory, or there is a failure in the system,
the system beeps and/or displays an error message after
the Power On Self Test (POST). If the failure is not
too severe, it will give you the opportunity to modify
the settings of the setup utility, as described in the
following steps:
1. When you turn on or restart the computer there is
a beep and/or the following message appears on
the screen:
Error message - please run SETUP
program Press <F1> key to continue,
<F2> to run SETUP
].
2. If an error message is displayed on the screen, and
you want to continue with the boot process and start
the operating system anyway, press the [
• If your notebook emits a series of beeps
• If your data security settings require it,
about the field to be displayed on the
right-hand side of the screen.
on a selection that is not a submenu or
auto selection will cause a list of all
options for that item to be displayed.
Pressing the Enter key again will select
the highlighted choice.
] key resets all items in the BIOS to
F9
] key saves the current configura-
F10
] key gives you a general help screen.
F1
that sounds like a code and the display is
blank, refer to the Troubleshooting Sec-
tion of your system User's Guide. The
Troubleshooting Section includes a list of
error messages and their meanings.
you may be asked for a password before
the operating system will be loaded.
] key.
F1