Brother QL-810W Посібник з швидкого налаштування - Сторінка 5
Переглянути онлайн або завантажити pdf Посібник з швидкого налаштування для Виробник етикеток Brother QL-810W. Brother QL-810W 10 сторінок. Dk label. dk tape
Також для Brother QL-810W: Посібник з швидкого налаштування (10 сторінок), Посібник з безпеки продукції (11 сторінок), Посібник з монтажу (5 сторінок), Посібник (2 сторінок)
Друкувати сторінку
6. Installing the Coin Cell Battery (QL-820NWB only)
A coin cell battery is used as a backup power supply to maintain the settings for the internal clock. Please
note that battery power will be consumed even if the Label Printer is not in use.
1.
Make sure that the Label Printer is turned Off.
Hold the Label Printer by the front, and firmly
lift the DK Roll Compartment Cover to open it.
2.
Pull out the insulation seal on the coin battery.
IMPORTANT
• Using a coin or similar object, slowly turn the coin cell battery cover in the direction of the arrow on the
battery cover until it stops, and then remove the coin cell battery cover.
Do not turn the coin cell battery cover past the unlock position, or you may damage it.
• Re-install the coin cell battery cover, using a coin or similar object to slowly turn the coin cell battery cover
in the opposite direction of the arrow cover until it locks into place.
Be sure to insert the new battery with the + and – sides facing the correct direction.
CAUTION
• Remove the battery if you do not intend to use the Label Printer for an extended period of time.
• Dispose of the battery at an appropriate collection point, not in the general waste stream. Be sure to
observe all applicable federal, state, and local regulations.
• When storing or discarding a battery, wrap it with cellophane tape to prevent it from short-circuiting.
(see illustration)
1. Cellophane tape
2. Coin Cell Battery
• We recommend replacing the battery every two
years.
7. Turning Power On/Off
On: Press the Power ( ) Button to turn the Label Printer On. The Status LED turns green.
Off: Press and hold the Power ( ) Button again to turn the Label Printer Off.
IMPORTANT
When turning the Label Printer Off, do not remove the battery or disconnect the AC Adapter until the
orange Status LED turns Off.
8. Setting LCD Language (QL-820NWB only)
1.
Press the Menu Button.
2.
Press the ▲ or ▼ Button to select the Administration menu, and then press the OK Button.
3.
Select [
9. LED Indications
The Label Printer's LED indicates the Label Printer's status.
QL-810W
Status LED
Not lit
Steady green
light
Flashing green
light
Steady orange
light
Flashing
orange light
Steady red
light
Flashing red
light
*
"Rapidly" means 0.3 second intervals.
Wi-Fi LED
Wi-Fi LED
1
Not lit
1 Cellophane tape
Flashing blue
2 Coin Cell battery
light
2
Steady blue
light
Battery LED
Battery LED
Flashing
orange light
Steady orange
light
Not lit
Language], scroll to select your language, and then press the OK Button.
Condition
Power Off.
Power On.
Feeding Mode / Printing Mode / Cutting Mode / Cleaning
Mode
If the green light flashes at 0.5 second intervals, one of the
following has occurred:
• Print preparation mode
• Receiving data from the computer
• Transferring data
• Searching for printers
The DK Roll Compartment Cover is open. Close the DK
Roll Compartment Cover correctly.
Label resetting mode is on or the Cutter Button was
pressed while resetting.
For more information on resetting the Label Printer, see
the User's Guide.
If the orange light flashes at 0.5 second intervals:
• The Label Printer is on cooling mode
Label Printer is booting.
If the red light flashes at 1 second intervals, one of the
following errors has occurred:
• End of DK Roll
• Feed error
• The DK Roll Compartment Cover was opened while the
Label Printer was in use.
• Transmission error
• Database search error
• Access point search error
• Access point connection error
• Security error
• No template selected
If the red light flashes rapidly*, there is a system error.
If the red light flashes at one second off, rapidly* on,
rapidly* off, rapidly* on, one of the following errors has
occurred:
• Cutter error
• Mass storage error
Condition
WLAN Off
If the blue light is on for 1 second, off for 2 seconds,
WLAN is on, but not connected.
WLAN is on and connected.
Condition
• If the orange light flashes once every second, the
battery needs recharging.
• If the orange light flashes twice every 4 seconds, the
battery power is low.
• If the orange light flashes once every 4 seconds, the
battery power is half.
The battery is charging.
The battery is fully charged.
QL-820NWB
Status LED
Condition
Not lit
Power Off.
Steady green
Power On.
light
Feeding Mode / Printing Mode / Cutting Mode / Cleaning
Mode
Flashing green
If the green light flashes at 0.5 second intervals, one of the
light
following has occurred:
• Print preparation mode
• Receiving data from the computer
• Transferring data
• Searching for printers
Steady orange
The DK Roll Compartment Cover is open. Close the DK
light
Roll Compartment Cover correctly.
Flashing
If the orange light flashes at 0.5 second intervals:
orange light
• The Label Printer is on cooling mode
Steady red
Label Printer is booting.
light
Flashing red
If the red light flashes at 1 second intervals, one of the
light
following errors has occurred:
• End of DK Roll
• Feed error
• The DK Roll Compartment Cover was opened while the
Label Printer was in use.
• Transmission error
• Database search error
• Access point search error
• Access point connection error
• Security error
• No template selected
If the red light flashes rapidly*, there is a system error.
If the red light flashes at one second off, rapidly* on,
rapidly* off, rapidly* on, one of the following errors has
occurred:
• Cutter error
• Mass storage error
*
"Rapidly" means 0.3 second intervals.