Brother MFC 640CW - Color Inkjet - All-in-One Посібник з швидкого налаштування - Сторінка 36
Переглянути онлайн або завантажити pdf Посібник з швидкого налаштування для Факсимільний апарат Brother MFC 640CW - Color Inkjet - All-in-One. Brother MFC 640CW - Color Inkjet - All-in-One 45 сторінок. Windows network connection
Також для Brother MFC 640CW - Color Inkjet - All-in-One: Посібник з швидкого налаштування (45 сторінок), Інструкція з ремонту (5 сторінок), Посібник з експлуатації (11 сторінок)
Друкувати сторінку
STEP2
Installing the Driver & Software
For Wireless Network Users
For Mac OS
Important
Make sure that you have finished the
instructions from Step 1 Setting Up the
Machine on page 4-11.
These instructions will install your Brother machine in a
typical small office or home wireless network environment
in infrastructure mode, using a wireless router or access
point that uses DHCP to assign IP addresses.
If you want to setup your machine in any other
wireless environment you can find instructions in the
Network User's Guide on the CD-ROM.
You can view the Network User's Guide by following
the instructions below.
1 Turn on your Macintosh
CD-ROM labeled Macintosh
drive.
2 Double-click the Documentation icon.
3 Double-click your language folder.
4 Double-click the Network User's Guide
BH3eWLAN_UsaEngNet.pdf.
To achieve optimum results with normal every day
document printing, place the Brother machine as
close to the network access point (router) as possible
with minimal obstructions. Large objects and walls
between the two devices as well as interference from
other electronic devices can affect the data transfer
speed of your documents.
Due to these factors, wireless may not be the best
method of connection for all types of documents and
applications. If you are printing large files, such as
photos on glossy paper or multi-page documents with
mixed text and large graphics, you may want to
consider choosing wired Ethernet for a faster data
transfer, or USB for the fastest throughput speed.
First you must configure the wireless network settings
of your machine to communicate with your network
access point (router). After the machine is configured
to communicate with your access point computers on
your network will have access to the machine. To use
the machine from these computers, you will need to
install the MFL-Pro Software Suite. The following
steps will guide you through the configuration and
installation process.
34
®
X 10.2.4 or greater in infrastructure mode
®
. Insert the Brother
®
into your CD-ROM
1
Write down the wireless network settings of
your access point or wireless router.
SSID (Service Set ID or Network name)
_________________________
WEP Key (if needed)
_________________________
WPA-PSK (TKIP) (if needed)
_________________________
The WEP key is for 64bit encrypted networks
or 128 bit encrypted networks and can contain
both numbers and letters. If you do not know
this information you should see the
documentation provided with your access point
or wireless router. This key is a 64-bit or 128-bit
value that must be entered in an ASCII or
HEXADECIMAL format.
For example:
64 bit ASCII:
Uses 5 text characters.
e.g. "Hello" (this is case sensitive)
64 bit
Uses 10 digits of hexadecimal data.
Hexadecimal:
e.g. "71f2234aba"
128 bit ASCII: Uses 13 text characters.
e.g. "Wirelesscomms" (this is case
sensitive)
128 bit
Uses 26 digits of hexadecimal data.
Hexadecimal:
e.g. "71f2234ab56cd709e5412aa3ba"
WPA-PSK enables a Protected Access Pre-
shared key that allows the Brother wireless
machine to associate with access points using
TKIP encryption. WPA-PSK uses a Pre-Shared
Key that is more than 7 and less than 64
characters in length.
Note
Your machine supports WEP and WPA-
PSK(TKIP). WPA-PSK(AES) is not supported.
See Chapter 3 of the Network User's Guide for
more details.
®
Macintosh