2N SmartGate UMTS Посібник - Сторінка 2

Переглянути онлайн або завантажити pdf Посібник для Шлюз 2N SmartGate UMTS. 2N SmartGate UMTS 2 сторінки.

2N SmartGate UMTS Посібник
2N® SmartGate UMTS QuickStart
Basic Functions
• Primarily, the device is intended for
voice
transmission
between
GSM/UMTS network and connected line
telephone sets.
• Detailed routing tables include a lot of
settings and help cut your call costs
dramatically.
• Using a PC, you can get access to the
high-speed
Internet
(GPRS,
Read the CD-ROM User Manual carefully to get familiar with all the 2N®
SmartGate UMTS functions.
2N® SmartGate UMTS supports the 3G WCDMA/HSDPA, GSM GPRS/EDGE
technologies for data connection. The connection speed and quality
depend on the UMTS/GSM provider, accessible services, signal coverage
and network conditions. The parameters included in the User Manual
(Technical Parameters) are the maximum values; for detailed information
about accessible services contact your mobile provider.
2N® SmartGate UMTS Installation and Connection
• Proper Location
- Install 2N® SmartGate UMTS with respect
to a good UMTS/GSM signal intensity.
- Place 2N® SmartGate UMTS out of range
of sensitive devices and human bodies for
electromagnetic interference reasons.
- 2N® SmartGate UMTS is designed for
indoor use. Do not place it near heat
sources. It may not be exposed to direct
solar radiation, rain, flowing water and
moisture, aggressive gas, solvents etc.
• Needed Accessories
INCLUDED IN 2N® SMARTGATE UMTS PACKAGE
• 1 2N® SmartGate UMTS
• 1 power adapter (12V/1A DC)
• 1 antenna including supply cable (SMA)
• 1 telephone cable
• 1 USB A/B cable
• 1 SMS input connector
• 2 screws with dowels
• 1 User Manual and SW CD
NOT INCLUDED IN 2N® SMARTGATE UMTS PACKAGE
• SIM card
WCDMA,
HSDPA)
and
the
SMS.
• You can send SMS to one pre-defined
number via a SMS input.
• The battery backed-up 2N® SmartGate
UMTS version allows you to maintain your
traffic even in the event of power outage.
• The 2N® SmartGate UMTS firmware can
EDGE,
be upgrade from www.2n.cz
• Provider's information on Internet
connection (APN, etc.)
• External Antenna Connection
Screw the enclosed antenna into the
SMA antenna connector. Tighten the
antenna connector gently with your
hand, never use a wrench!
• SIM Card Installation
Insert the SIM card into the SIM card
slot on the 2N® SmartGate UMTS
bottom (connector) side as shown in
the figure and make sure that the
security latch has clicked into position.
Select the required provider and SIM
card services, such as call forwarding,
call barring, preferred networks, SMS
centre, etc., using your mobile phone
before inserting your SIM card in 2N®
SmartGate UMTS.
• Connection to FXO Interface
A device with the FXS interface can be
connected to the FXO interface (e.g. a
PBX internal line).
• Connection to FXS Interface
A device with the FXO interface can be
connected to the FXS interface (a
standard
answering machine, PBX external line).
send/receive
2N® SmartGate UMTS is equipped with
the FSK-based CLIP function on the
FXS interface and so you are advised to
connect a
device.
• Mains
Switch On
2N® SmartGate
voltage powered. Connect the attached
Do not connect the antenna as long as the device is in operation to avoid
GSM/UMTS module damage.
Power switch
(backed-up version)
Power adapter
IN: 110V-240V AC
OUT: 12V/1A DC
LED Indicators
Power
supply
GSM
UMTS
Telephone
line
Signal/
Battery
indicator
By entering three wrong PINs you block the SIM card. Enter the PUK code
into your mobile phone to unblock the SIM card.
analogue
telephone,
• Battery
CLIP displaying terminal
Supply
Connection
and
UMTS
is
12V
DC
Example of 2N® SmartGate UMTS Connection
ON/OFF
Analogue
telephone
PC (USB)
(FXO interface)
SIM
1. Hook off the telephone and hear the PIN
Blue light – mains supply
tone:
Yellow light – battery supply
2. Enter the PIN using DTMF and press
Blue flashing –logged out
Blue light – logged in
for confirmation. Hang up the line to
cancel a wrong PIN.
No light – Standby
Orange LED – FXS interface active
3. If you hear the busy tone after a while (a
Green LED – FXO interface active
few seconds), the PIN has been entered
Flashing – line off-hook or ringing
correctly.
Light – call in progress
Alternating LED – call FXS - FXO
automatically upon every power up.
1 is shining – minimum
4. If you hear the PIN tone again after a
4 are shining – maximum
while, the PIN has not been entered
Signal – during ready state
Battery –upon off-hook on FXS line
correctly. Re-enter the PIN.
power adapter (12V/1A DC) to the
power
supply
connector.
After
connection, switch on 2N® SmartGate
UMTS with the power switch on the
right-hand bottom side.
Supply
Connection
and
Switch On
Insert four AA-type batteries into a
compartment on the back side of the
backed-up
2N®
SmartGate
UMTS
gateway. Refer to the compartment
label for proper battery placement and
polarity.
SMS input
PBX internal line
(FXS interface)
PIN Secured SIM Card
This
PIN
will
be
entered