Fujitsu fi-5530C - Document Scanner Початок роботи - Сторінка 12

Переглянути онлайн або завантажити pdf Початок роботи для Принтер Fujitsu fi-5530C - Document Scanner. Fujitsu fi-5530C - Document Scanner 28 сторінок. Color departmental scanner
Також для Fujitsu fi-5530C - Document Scanner: Посібник з інсталяції Посібник з інсталяції (7 сторінок), Посібник з інсталяції Посібник з інсталяції (9 сторінок), Процедури встановлення (3 сторінок), Початок роботи (28 сторінок), Брошура та технічні характеристики (2 сторінок), Технічні характеристики (2 сторінок), Інструкції із заміни витратних матеріалів та очищення (14 сторінок), Інструкція з очищення Посібник з очищення (13 сторінок), Інструкція з експлуатації (10 сторінок)

Друкувати сторінку
Fujitsu fi-5530C - Document Scanner Початок роботи
2. Connect the other end of the USB interface
cable to your PC.
•
Be sure to use the USB cable which
ATTENTION
comes with this scanner as an acces-
sory. Correct operation with commer-
cially available cables is not guaranteed.
•
When connecting to an USB hub, use
the first stage USB hub that is closest to
the computer. If you use the second or
later hub stages, the scanner may not
operate correctly.
•
If you connect the scanner with USB 2.0,
it is required that the USB port and Hub
are compliant with USB 2.0. The scan-
ning speed may slow down if it is con-
nected with USB1.1.
■ Connecting with the SCSI Inter-
face Cable
When using the scanner with a SCSI interface, the fol-
lowing SCSI interface cable and SCSI card must be pur-
chased.
• SCSI interface cable:
Use a cable which complies with a 50 Pin Con-
tact Shielded High-Density SCSI Device Con-
nector for Ultra SCSI.
• SCSI card
Find the recommended SCSI card information in
the Fujitsu web site (FAQ).
http://imagescanner.fujitsu.com/
•
When connecting the SCSI interface
ATTENTION
cable, turn the scanner off. Be sure to
connect the SCSI interface cable first ,
and then turn on the power of the scan-
ner and PC.
•
In a SCSI daisy chain formation, con-
nect the scanner so that it is the termi-
nated device.
1. Insert the SCSI interface cable into the inter-
face connector of the scanner until both sides
click.
4
2. Connect the other end of the cable to your PC.
Be careful not to bend the pins of the SCSI
ATTENTION
cable when connecting to the scanner .
The SCSI ID initially set at the factory is "5".
HINT
If the SCSI ID of another SCSI device is set
to the same ID, either change the scanner's
SCSI ID or SCSI ID of the other SCSI
device. For details on how to change the
SCSI ID, refer to " Setting the SCSI ID" in
this section.

■ Setting the SCSI ID

The factory initial setting for SCSI ID is "5".
1. Press the power button at least for two sec-
onds to turn off the scanner if it is on. Discon-
nect the AC cable from the outlet.
2. Set the SCSI ID using the SCSI ID switch on
the back of the scanner.
Click
ID No.
0 to 7
Can be set as the ID
Works with the factory default value
8, 9
(SCSI ID = 5).
3. Press the power button to turn ON the scanner.
When the scanner is turned ON, the SCSI ID set
at step 2 is enabled.
Description