Indesit ITW E 71252 Посібник - Сторінка 6
Переглянути онлайн або завантажити pdf Посібник для Пральна машина Indesit ITW E 71252. Indesit ITW E 71252 12 сторінок.
Друкувати сторінку
CONSUMPTION DATA
Tempe-
Load
Water
Programme
rature
(°C)
(kg)
Cotton
95
7.0
58*
Cotton
60
7.0
52
Cotton
40
7.0
52
Eco Cotton
**
60
7.0
50
Eco Cotton
**
60
3.5
35
Eco Cotton
**
40
3.5
35
Synthetics
60
3.0
50*
Synthetics
40
3.0
40
Delicate
40
1.5
50
Delicate
30
1.5
50
Wool
40
1.0
40
Wool
20
1.0
40
Mix Colored
40
3.0
40
Jeans
40
4.0
52
Home Mix
60
3.5
55
New Born
60
4.0
57
15' Refresh
30
3.0
30
Express 30
30
3.0
42
Mini & Fast
30
1.0
25
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect
to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.Water and energy consumption refer to the
default setting of the programmes; selecting special options or modifying spin speed or temperature will change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
"Troubleshooting Guide" in your Instructions for Use).
Approximete remaining moisture content (%). After programme end and spinning with maximum selectable spin speed, in default programme setting.
*
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
**
Reference Programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.
PREPARATION OF THE WASH CYCLE
1.
Load the washing machine, close the drum door and check
that it is closed properly.
2. Pour in the detergent and any additives, as described
overleaf and in the instruction manual.
3. Close the lid.
4. Turn the programme selector to the desired programme.
The display shows the duration of the selected programme
(in hours and minutes), and the indicator for the "Start/
Pause" button flashes. The temperature and spin speed
can be changed by pressing the "Temperature" and
"Spin Speed/ Rinse Hold" buttons. After the end of a
programme, or when a programme is selected but not
yet started, the washing machine will therefore switch off
automatically after about a quarter of an hour. To switch the
washing machine on again, turn the programme selector to
"Off" and afterwards to the desired programme again
SELECT ANY DESIRED OPTION
When the combination of programme and additional option(s)
is not possible, the indication lights switch off automatically.
Unsuitable combinations of options are deselected
automatically.
"Easy Ironing" button
• Reduces creasing by an increased water quantity and a very
gentle spin.
"Prewash" button
• Only for heavily soiled loads (for example sand, granular
dirt) sensible. Increases the cycle time by approximately 15
min.
• Do not use liquid detergent for the main wash when
activating the Prewash option.
Power consumption in off-mode 0.11 W / in left-on mode 0.11 W
Energy
Approx. Programme Duration
without "Time Saver"
without "Time Saver" with "Time Saver"
(l)
(kWh)
2.10
2:35
1.33
2:30
0.80
2:25
1.05
3:40
0.84
2:45
0.65
2:00
0.90
2:05
0.50
1:50
0.55
0:45
0.50
0:41
0.55
0:35
0.10
0:30
0.45
1:00
0.58
1:30
1.10
2:00
0.90
1:30
0.15
0:15
0.25
0:30
0.22
0:45
"Extra Rinse" button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with very soft
water, washing baby linen and helping people with allergies.
"Soil Level" button
• Adapts the programme duration to the soil level of your
laundry. Also influences the detergent quantity.
=lightly soiled -
=normaly soiled -
• Not all soil levels are selectable for each programme.
"Spin Speed/ Rinse Hold" button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If you select spin speed "0", the final spinning is cancelled and
the water is drained out only. However, intermediate spin
phases remain during the rinse.
• If you select "Rinse hold", the laundry remains in the last
rinse water without progressing to the final spin cycle,
to avoid creasing and prevent colours from changing. To
activate the "Rinse hold", press the "Spin" button repeatedly
until the "Rinse hold" symbol on the display lights up.
- The wash programme stops to "Rinse hold" when the "Rinse
hold" symbol on the display blinks; the light of "Start/
Pause" button also blinks.
- To terminate the "Rinse hold" by spinning the laundry, press
"Start/Pause" - the laundry will be spun with the default
spin speed. You can also select another spin speed with the
"Spin" button before you start the spin cycle by pressing
"Start/Pause".
- To terminate the "Rinse hold" by draining the water without
spinning, press the "Spin" button until spin speed "0" appears
on the display; then press "Start/Pause" to start the
draining. Do not leave the laundry to soak for too long in the
"Rinse hodl" (especially silk).
"Energy Saver" button
• Saves energy used for water heating while maintaining good
(hrs : min)
wash result.
• Recomentable for lightly soiled laundry without stains.
%
• Make sure that your detergent is suitable for cold wash
2:00
temperatures (15 or 20 °C).
• Mainly selectable on the lowest temperature step of the
1:45
57
programmes.
1:30
"Time Saver" button
-
• Enables quicker washing by shortening the programme
-
53
duration.
-
• Recommendable for small loads or only lightly soiled
laundry.
1:14
40
0:59
DELAY TIMER
-
The "Delay Timer" button allows the user to run the machine
-
at his convenience, for example at night when electricity is
-
cheaper.
• Do not use liquid detergent when activating this function.
-
• Select programme, spin speed and options.
-
61
• Press the "Delay Timer" button several times to select a
1:10
delay time by 1 to 23 hours.
-
• Start the programme (see "Progremme Start"). The
1:10
indication lamp over the "Delay Timer" button lights up and
-
goes off when the programme starts.
• Once having pressed the "Start/Pause" button, the
-
countdown of the time delay begins. The time delay
-
indication on the display disappears when the programme
starts and is replaced by the remaining time.
• After the "Start/Pause" button has been pressed, the
number of hours preselected can be reduced by pressing
again the "Delay Timer" button.
To cancel the "Delay Timer"
..before you press the "Start/Pause" button:
• Turn the programme selector to another position or press
the "Reset/Drain" button.
..after having pressed the "Start/Pause" button:
• Press the "Reset/Drain" button for at least 3 second. The
start delay indicator light goes off.
PROGRAMME START
=heavily soiled.
Open the tap and press the "Start/Pause" button. The
blinking light next to the "Start/Pause" button becomes
constant. The programme sequence indicator shows the
current programme phase, running from left to right through
Wash, Rinse, Spin/Drain. When the programme phrase is
finised, the corresponding indication goes out.
"DOOR LOCKED" INDICATION
After start of a program the lamp lights up to indicate that the
lid can not be opened. As long as a wash programme is running,
the lid remains locked and must on no account be forced open.
In case you have an urgent need to open it during a running
programme, refer to "Cancel a running programme before the
end".
CHILD LOCK BUTTONS
You can lock the buttons of the control panel against improper
use (e.g. by children).
• Press both of the child lock buttons simultaneously and hold
them for at least 3 seconds. The key symbol on the display
lights up.
• To unlock the buttons again: proceed in the same way.
FAILURE INDICATIONS
In case of any failures or irregularities, consult the
"Troubleshooting Guide" in your Instructions for Use.
"Water tap closed" -
No or not sufficient inlet water.
"Service" -
Failure or malfunction of an electrical component.
"Clean pump" -
Waste water is not pumped out.
Spin speed on display blinks: unbalance during
spinning
PROGRAMME END
•
The "Door locked" indication lights off and the display
shows "End". After about a quarter of an hour, the washing
machine will switch off completely to save energy.
1. Turn the programme selector to the "Off" position.
2. Close the water tap.
3. Open lid and drum and unload the machine.
4. Leave the lid open for some time to allow the interior of the
machine to dry.
DETERGENT OVERDOSAGE INDICATION
The symbol will light up at the end of the programme if you
used too much detergent. use less detergent next time. If the
symbol lights up and the display shows "Fod", too much foam
interrupted the wash process; refer to the "Troubleshooting
Guide" in your Instructions for use.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1.
Press the "Start/Pause" button to pause the programme.
The light blinks.
2. Select the new programme, temperature, any options and
another spin speed if you want.
3. Press the "Start/Pause" button again. The new programme
continues at the same position where the previous
programme was interrupted. Do not add detergent for this
programme.
CANCEL A RUNNING PROGRAMME BEFORE THE
END
The "Reset/Drain" button cancels a programme before the
end.
• Press the "Reset/Drain" button for at least 3 seconds. The
water is drained out; it may last a while until you can open
the lid.