Indesit DISP 5377 Інструкція з експлуатації Посібник з експлуатації - Сторінка 26
Переглянути онлайн або завантажити pdf Інструкція з експлуатації Посібник з експлуатації для Посудомийна машина Indesit DISP 5377. Indesit DISP 5377 28 сторінок.
Друкувати сторінку
Troubleshooting
Whenever the appliance fails to work, check for a solution from the following list before calling for
EN
Assistance.
Problem:
The dishwasher does not start or
cannot be controlled
The door won't close
No water drains out from the
dishwasher.
The dishwasher makes excessive
noise.
The dishes and glasses are
covered in a white film or
limescale deposits.
The dishes and glasses are
streaked or have a bluish tinge.
The crockery has not been dried
properly.
The dishes are not clean.
The dishwasher does not take any
water in - Tap shut-off alarm
(several short beeps are emitted)
(the ON/OFF indicator light flashes
and the number 6 appears on the
display).
Water inlet hose alarm / Water inlet
filter blocked
(the ON/OFF indicator light flashes
and the number 7 appears on the
display).
*
26
Possible causes / Solutions:
• Switch off the appliance by pressing the ON/OFF button, switch it back on after
approximately one minute and reset the program.
• The appliance has not been plugged in properly.
• The dishwasher door has not been shut properly.
• The lock was released. Strongly push the door until a "clacking" noise is heard.
• The dishwasher cycle has not yet finished.
• The water inlet hose is bent (see Installation).
• The drain duct is blocked.
• The filter is clogged up with food residues.
• The dishes are rattling against each other or against the sprayer arms.
• An excessive amount of foam has been produced: the detergent has not been
measured out correctly or it is not suitable for use in dishwashers (see Start-up
and use).
• The level of the refined salt is low or the dosage setting is not suited to the
hardness of the water (see Rinse aid and salt).
• The lid on the salt dispenser is not closed properly.
• The rinse aid has been used up or the dosage is too low.
• The rinse aid dosage is too high.
• A wash cycle without a drying program has been selected.
• The rinse aid has been used up or the dosage is too low (see Rinse aid and
salt).
• The rinse aid dispenser setting is not suitable.
• The crockery is made from non-stick material or plastic.
• The racks are overloaded (see Loading the racks).
• The crockery has not been arranged well.
• The sprayer arms cannot move freely.
• The wash cycle is too gentle (see Wash cycles).
• An excessive amount of foam has been produced: the detergent has not been
measured out correctly or it is not suitable for use in dishwashers (see Start-up
and use).
• The lid on the rinse aid compartment has not been shut correctly.
• The filter is dirty or blocked (see Care and maintenance).
• The refined salt level is low (see Rinse aid and salt).
• There is no water in the mains supply.
• The water inlet hose is bent (see Installation).
• Turn on the tap and the appliance will start after a few minutes.
• The appliance lock has been activated because no action was taken when the
beeps sounded.
Switch off the appliance using the ON/OFF button, turn on the tap and switch
the appliance back on after 20 seconds by pressing the same button. Re-
program the appliance and restart the wash cycle.
• Switch off the appliance by pressing the ON/OFF button. Shut off the water tap
to eliminate the risk of flooding and remove the plug from the electrical socket.
Make sure the water inlet filter has not become blocked by impurities (see "Care
and maintenance" chapter).