Indesit I6GG1/UK Інструкція з експлуатації Посібник з експлуатації - Сторінка 3

Переглянути онлайн або завантажити pdf Інструкція з експлуатації Посібник з експлуатації для Кухонні плити Indesit I6GG1/UK. Indesit I6GG1/UK 12 сторінок.
Також для Indesit I6GG1/UK: Інструкція з експлуатації Посібник з експлуатації (13 сторінок)

Друкувати сторінку

Indesit I6GG1/UK Інструкція з експлуатації Посібник з експлуатації

Gas connection

T he cooker should be connected to the gas-supply

by a corgi registered installer. During installation of

this product it is essential to fit an approved gas tap

to isolate the supply from the appliance for the

convenience of any subsequent removal or

servicing. Connection of the appliance to the gas

mains or liquid gas must be carried out according to

the prescribed regulation in force, and only after it is

ascertained that it is adaptable to the type of gas to

be used. If not, follow the instructions indicated in

the paragraph headed "Adaptation to different gas

types". On some models the gas supply can be

connected on the left or on the right, as necessary;

HOT PARTS

regulation in force. The gas supply must be

connected to the left of the appliance. Be sure that

the hose does not pass through the rear of the

cooker touching hot parts.

! Make sure the supply pressure conforms with the

values shown in the table entitled "Caracteristics of

the burners and nozzles". When the cooker is

installed between cabinets (recessed), the

gas connection must be effected by an

approved flexible hose with bayonet fitting

(BS 669 Current Edition). The gas inlet for

the cookers is a threaded G 1/2 gas female

f i t t i n g .

Connecting the gas supply

To make the connection, a flexible hose should be

used corresponding to the current gas regulations

which are:

• the hose must never be at any point in its lenght

in contact with the "hot" parts of the cooker;

• the hose must never be longer than 1,5 metre;

• the hose must not be subject to any tension or

torsional stress and it must not have any

excessively narrow curves or bottlenecks;

• the hose must be easy to inspect along its entire

length to check its condition;

to change the

connection, reverse the

position of the hose

holder with that of the

cap and replace the

gasket (supplied with

the appliance). In the

case of connection to

liquid gas, by tank, use

pressure regulators that

conform to the

When the cooker is

• the hose must always be in good condition, never

attempt to repair.

! The installation must comply with gas safety

(installation and use) regulations 1984. In all cases

for the above, by low, a qualified, corgi approved

engineer must be called for installation.

Electrial connection

Power supply voltage and frequency: 230-240V a.c.

50/60 Hz.

! ! ! ! ! The supply cable must be positioned so that it

never reaches at any point a temperature 50°C

higher than the room temperature. The cable must

be routed away from the rear vents. Should you

require it, you may use a longer cable, however, you

must ensure that the cable supplied with the

appliance is replaced by one of the same

specifications in accordance with current standards

and legislation.

Your appliance is supplied with a 13 amp fused plug

that can be plugged into a 13 amp socket for

immediate use. Before using the appliance please

read the instructions below.

WARNING - THIS APPLIANCE MUST BE

EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE

CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be used,

and the fuse cover re-fitted. If the fuse cover is lost,

the plug must not be used until a replacement is

obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of

the correct colour as indicated by the coloured

marking or the colour that is embossed in words on

the base of the plug. Replacements can be obtained

directly from your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug

and you should wish to remove it to add a cable

extension or to re-route the mains cable through

partitions, units etc., please ensure that either:

• the plug is replaced by a fused 13 amp re-

wireable plug bearing the BSI mark of approval.