Indesit ID50C1 S Інструкція з експлуатації Посібник з експлуатації - Сторінка 5
Переглянути онлайн або завантажити pdf Інструкція з експлуатації Посібник з експлуатації для Кухонні плити Indesit ID50C1 S. Indesit ID50C1 S 24 сторінки. 50cm free standing electric cooker
Також для Indesit ID50C1 S: Інструкція з експлуатації Посібник з експлуатації (24 сторінок)
Друкувати сторінку
Installation
WARNING – THIS APPLIANCE MUST BE
WARNING – THIS APPLIANCE MUST BE
WARNING – THIS APPLIANCE MUST BE
WARNING – THIS APPLIANCE MUST BE
WARNING – THIS APPLIANCE MUST BE
E A R T H E D .
E A R T H E D .
E A R T H E D .
E A R T H E D .
E A R T H E D .
Electrical connection
Electric cookers come without a power supply cable.
The cooker is designed to operate on an electricity
supply which conforms to the electrical data shown
on the Rating Plate. The cooker can be connected to
the mains only after removing the back panel of the
cooker itself with a screwdriver.
! ! ! ! ! The following installation procedure must be
carried out by a qualified electrician. The electrical
installation must comply with the IEE Regulations,
Building & local By-Lays.
For the installation of the feeding cable carry out the
following operations:
under the screw heads, respecting
the colour code: Black/Blue (N), Red/Brown
(L) and Bare Wire/Yellow-Green (
Once the connections have been made, tighten all
the terminal screws fully.
Fasten the supply cable in place with the clamp
and close the cover of the terminal board.
N.B.:
N.B.: the power supply cable must have these minimum
N.B.:
N.B.:
N.B.:
requirements:
Type:
H05RR-F
H05VV-F
Section: 3x4 mm
2
1 Open the terminal
board by inserting a
screwdriver into the
side tabs of the cover.
Use the
screwdriver as a
lever by pushing it
down to open the cover
(see diagram).
2 Loosen the cable
clamp screw and
remove it, using a
screwdriver as a lever
(see figure).
3 Remove the wire
contact screws L-N-
,
then fasten the wires
).
Positioning the Cooker
150 mm
150 mm
Moving the Cooker
standing.
Adjacent side walls which project above hob level,
must not be nearer to the cooker than 150mm and
should be protected by heat resistant material.
Any overhanging surface or cooker hood should
not be nearer than 650mm.
Before moving your cooker check that it is cool,
and switch off at the cooker control unit.
Movement of your cooker is most easily achieved
by lifting the front as follows:
Open the grill door sufficiently to allow a
comfortable grip on the underside front edge of
the oven roof, avoiding any grill elements.
Note: Take care in moving the cooker as it is
Note:
Note:
Note:
Note:
heavy. Take care to ensure that any floor covering
is not damaged.
Splashplate optional, apply to Parts Department
(see Back Cover for contact number.)
The height of the
cooker can be
adjusted by
means of
adjustable feet in
the plinth (900mm
- 915mm). Adjust
the feet by tilting
the cooker from
the side. Then
install the product
into position.
NOTE: This
appliance must
not be fitted on a
platform.
The cooker is
designed to fit
between kitchen
cabinets spaced
500mm apart. The
space either side
need only be
sufficient to allow
withdrawal of the
cooker for
servicing. It can
be used with
cabinets one side
or both as well as
in a corner setting.
It can also be
used free-
5
GB