Indesit ID50G Інструкція з експлуатації Посібник з експлуатації - Сторінка 6

Переглянути онлайн або завантажити pdf Інструкція з експлуатації Посібник з експлуатації для Кухонні плити Indesit ID50G. Indesit ID50G 24 сторінки. 50cm free standing gas cooker

Друкувати сторінку

Connect Blue wire to terminal marked "N" or coloured Black.

If a 13 amp plug (BS 1363) is used it must be fi tted with a 13

amp fuse. A 15 amp plug must be protected by a 15 amp

fuse, either in the plug or adaptor or at the distribution

board. If you are in any doubt about the electrical supply to

your machine, consult a qualifi ed electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in accordance

with the following code:

BLUE

"NEUTRAL" ("N")

BROWN "LIVE" ("L")

GREEN AND YELLOW

"EARTH" ("E")

WARNING.

If the electric supply fails to this appliance you must

not use the grill or ovens.

Disposing of the appliance

When disposing of the appliance please remove the plug

by cutting the mains cable as close as possible to the plug

body and dispose of it as described above.

Adapting the cooker to diff erent types of gas

In order to adapt the cooker to a diff erent type of gas with

respect to the gas for which it was produced (indicated on

the label attached to the lid), follow these steps:

a) replace the hose holder mounted on the appliance with

that supplied in the bag of "cooker accessories".

b) Replacing the burner nozzles on the hob:

• remove the grids and slide the burners from their

housings;

• unscrew the nozzles using a 7

mm socket spanner, and replace

them with nozzles for the new

type of gas (see table 1 "Burner

and nozzle characteristics").

• replace all the components by

repeating the steps in reverse

order.

c) Minimum regulation of the hob burners:

• turn the tap to minimum;

• remove the knob and adjust the regulation screw, which

is positioned in or next to the tap pin, until the fl ame is

small but steady.

GREEN &

YELLOW

13 amp fuse

BROWN

CROSS-BAR

BLUE

CORD GRIP

! in the case of liquid gas, the regulation screw must be

screwed in to the bottom.

• check that the fl ame does not turn off when you turn the

tap quickly from high to low.

d) Regulating the primary air of the burners:

The primary air of the burners requires no regulation.

Adapting to diff erent types of gas

In order to adapt the oven to a diff erent type of gas with

respect to the gas for which it was manufactured (indicated

on the label), follow these simple steps:

a) Replacing the oven burner nozzle

• open the oven door fully

• pull out the sliding oven bottom

unscrew the two screws and take off the shield

protecting the burner (in main oven burner only).

• Pry the fi xing tab "V" and remove the oven burner

• Unscrew the oven burner nozzle using the socket

spanner for the nozzles "Z", or a 7 mm socket spanner,

and replace it with a nozzle suited to the new type of gas

(see Table 1).

Take particular care handling the spark plug wires and

the thermocouple pipes.

• Replace all the parts, following the steps described

above in the reverse order.

b) Minimum regulation of the gas oven burner with

thermostat:

• light the burner as described in the paragraph "the oven

knob" of the instruction booklet.

• turn the knob to Max for about 10 minutes and then turn

the knob to the Min setting;

• remove the knob;

• regulate the screw positioned outside the thermostat

pin until the fl ame is small but steady.

! in the case of liquid gas, the regulation screw must be

screwed in to the bottom.