Indesit EWDE 7125 Інструкція з використання Посібник з використання - Сторінка 13
Переглянути онлайн або завантажити pdf Інструкція з використання Посібник з використання для Пральна машина / сушарка Indesit EWDE 7125. Indesit EWDE 7125 16 сторінок.
Друкувати сторінку
Troubleshooting
Your Washer-dryer could fail to work. Before contacting the Technical Assistance Centre (see "Assistance"), make sure that
the problem cannot be solved easily using the following list.
Problem:
The machine does not switch on.
The wash cycle does not start.
The machine does not dry.
The clothes are too hot when the
drying cycle is finished.
The machine does not fill with wa-
ter or 'H2o' is shown in the display
window.
The machine continuously fills with
water and continually drains away
or Water left in the drum
or Stuck on wash.
The machine does not drain or spin
(error lights flashing).
The wash programme takes too
long.
The Display sticks at one 'time to
end' for more than 1 Minute or the
Display changes the estimated 'Time
to End' during the programme.
The machine vibrates a lot during
the spin cycle.
Possible causes / Solutions:
• The appliance is not plugged into the socket fully, or not enough to make contact.
• There is no power to the socket, or the fuse has blown in the mains plug.
• The door is not closed properly.
• The ON/OFF button has not been pressed.
• The START/PAUSE button has not been pressed.
• The water tap has not been turned on to allow water to flow into the machine.
• A delayed start has been set.
• Check the 2 sections above.
• The 'DRY' button has been pressed to exclude drying.
• A cooling-down period is always added to the end of each drying cycle. If the
clothes appear too hot to handle leave the door open to allow to cool further
before removing from the machine.
• The water inlet hose is kinked.
• The water inlet hose is not connected to the water supply.
• The water pressure is too low.
• The water tap has not been turned on to allow water to flow into the machine.
• There is no water supply to the house.
• The inlet valve filter is blocked.
• The START/PAUSE button has not been pressed.
• The top of the drain hose is too low - It must be fitted at a height between 65
and 100 cm from the floor (see "Installation").
• The drain hose is connected incorrectly to the sink trap allowing water to run into
the machine, the drain hose must be positioned higher than the bottom of the
sink to prevent water flowing down the drain hose.
• The end of the drain hose has been pushed too far down the standpipe, the 'U'
bracket should be fitted 100 mm from the end of the drain hose.
• The Pump filter is blocked.
• The "Easy iron" option has been activated: To complete the wash cycle, press
the START/PAUSE button (see "Wash cycles and options").
• The drain hose is kinked (see "Installation").
• New Installation - The blanking cap or spigot has not been removed if
connected under a sink.
• The drain hose or sink trap is blocked.
• Programme times will vary due to water pressure, the incoming water temperature
and if the wash load goes out of balance. This will increase the programme times
accordingly (see ' The machine wont spin properly' next page) - (Most Common
Cause!).
• The display time is for guidance only - it is not a precise time to finish and
may vary.
• The feet have not been adjusted, enabling the machine to rock.
• New Installation - Either the Transit Bolts including the plastic spacers, or the
Polystyrene Packaging have not been removed when installing the machine.
• The machine is trapped between cabinets and/or walls.
• The load is in a slight out of balance condition and machine is spinning, but at
a lower speed.
GB
13