Kohler Centerpiece K-2264 Інструкція з монтажу Посібник з монтажу - Сторінка 4

Переглянути онлайн або завантажити pdf Інструкція з монтажу Посібник з монтажу для Сантехніка для ванної кімнати Kohler Centerpiece K-2264. Kohler Centerpiece K-2264 16 сторінок. Countertop and undercounter lavatories
Також для Kohler Centerpiece K-2264: Посібник для власників житла (16 сторінок), Посібник для власників житла (24 сторінок)

Друкувати сторінку

Kohler Centerpiece K-2264 Інструкція з монтажу Посібник з монтажу

Lift lavatory out of countertop with fitting and drain attached, if

applicable.

. Refer to Fig. #6 . Cut out inside of cut-out template with

scissors on the inside line.

Fig. #6

Refer to Fig. #7 . Set the cut-out template on the countertop

so the backsplash locator line is touching the countertop

backsplash. The cut-out template can be moved forward from this

position to get the best placement of the lavatory on the countertop.

Trace the cut-out opening on the countertop using a soft lead pencil.

Centerlines are provided to help align opening. Mark the final

centerline on the countertop using the cut-out template. Drill the

faucet holes using the following chart to determine their size.

NOTE: If there is not enough room at the front of the counter for

the lavatory rim, a larger countertop is needed.

Dimensions Are For Kohler Faucets Only. When Using Other

Faucets, Contact Supplier For Installation Instructions And

Dimensions.

FAUCET CENTERS

4" (10.2cm)

6" (15.2cm)

8" (20.3cm)

12" (30.5cm)

16" (40.6cm)

Faucet Escutcheon

Backsplash

Countertop

1007251-2-

VALVE HOLES

SPOUT HOLE

1-3/16" (3cm)

1-3/8" (3.5cm)

1-3/16" (3cm)

Handle Escutcheon

Centerline

1/4" (6mm) Min.

Fig. #7

Refer to Fig. #8 . Drill a pilot hole into the countertop using a

1/2" drill. Use a saber or keyhole saw to cut out opening by carefully

following the pencil line traced from cut-out template. Temporarily

position lavatory into counter, and trace a light pencil line around

the outside edge. This will serve as a guideline for applying sealant.

Remove fixture from countertop.

NOTE: The rim must be traced so the sealant will cover and

conceal the pencil line.

Install faucet to countertop and drain to lavatory following

manufacturer's instructions.

Refer to Fig. #9 . Apply two ribbons of plumbers putty or other

sealant on the counter from the edge of the opening to edge of rim

as measured in Step 5 according to the putty manufacturer' s

instructions. Quickly spread putty or sealant with a putty knife.

Plumbers Putty

Set lavatory into position. Immediately wipe away any excess

putty or sealant with a damp cloth. Fill in any voids between rim and

countertop.

Allow putty or sealant to set for 30 minutes. Connect supply

lines at supply valves and fitting. Assemble adjustable drain pop-up

linkage. Connect drain, trap, and outlet. Turn tailpiece into drain

body. Align trap inlet with tailpiece. Insert trap nut and gasket onto

tailpiece, and insert into trap. Tailpiece must extend 1" to 2" into trap.

Tailpiece may have to be cut to fit. Turn on water and check for leaks.

. CARE AND CLEANING. DO NOT USE ABRASIVE

CLEANSERS as they may scratch the surface of this fixture.

Clean up with a non-abrasive cleaner. Stubborn stains, paint, or tar

may be removed with turpentine or paint thinner.

Fig. #8

Lavatory

Countertop

Fig. #9

Kohler Co.