Kohler URBANITY 25717T-9 Інструкція з монтажу - Сторінка 4
Переглянути онлайн або завантажити pdf Інструкція з монтажу для Сантехніка для ванної кімнати Kohler URBANITY 25717T-9. Kohler URBANITY 25717T-9 4 сторінки. Recessed thermostatic dual shower faucet-multifunction showerhead
Друкувати сторінку
5
7
14
16
15
Cold
6
Hot
14
13
(Not provided)
Water Pressure Test
As figure 5 shown, uninstall the protectors(6) with screwdriver(not provided). Remove the plugs(14) with 8mm hex wrench
(13, not provided). Flush water supply pipes for about one minute to remove any debris. Reinstall the plugs. Remove the
protector cap(15) from the protector(7), and connect the connection(16) with one waterpipe(not provided).
As figure 6 shown, remove the screws(17) from the protector(8) with screwdriver(not provided) and pull it out. Remove the
connectors(18) with 8mm hex wrench, take off the filter washers(19). Flush water supply pipes for about one minute to
remove any debris. Insert two G1/2˝ plugs(not provided) into the connections(20).
Apply water pressure(8bar) test on the product. Check for leaks. Turn off the water supplies.
Remove two G1/2˝ plugs from the connections(20). Reinstall the filter washers(19) and connectors(18). Remove the
waterpipe from the connection(16). Reinstall the protector cap(15) and protectors(6, 8).
As figure 7 shown, ensure the out surface of the finished wall is between the MAX and MIN marks on the protectors(6, 8).
8
23
7
21
14
21
14
22
13
(Not provided)
Install the Faucet Body
Cut off the protectors(6) beyond the wall after the wall is finished. As figure 8 shown, uninstall and discard the plugs(14)
from the connections(21) with 8mm hex wrench(13, not provided). Remove the screws(22) from the protector(7) with
screwdriver(not provided) and pull it out. Check whether the O-rings on the connections(21) and showerhead tubes(23)
are intact.
As figure 9 shown, adjust two screws(25) with 3mm hex wrench(24). Install the faucet body to the connections(21) and
showerhead tubes(23) until it is against the finished wall. Tighten two screws(25) with 3mm hex wrench. Press the
plugs(26) into the faucet.
1418848-2A-C
6
7
18
The finished wall
8
17
8
20
6
19
18
9
The finished wall
23
21
21
25
26
24
10
18
8
91º
Install the Shower Arm
As figure 10 shown, when the finished wall is completed, remove the screws(17) from the protector(8) with screwdriver
(not provided) and pull it out. The angle between connectors(18) and finished wall should be 91 degrees.
As figure 11 shown, loosen the screws(28, 29) with 2.5mm hex wrench(27). Slide the escutcheon(30) onto the shower
arm(31). Install the shower arm with escutcheon onto the connectors(18), tighten the screws(29) with 2.5mm hex wrench
to secure the shower arm. Remain the protector cap(32) on the shower arm before the showerhead is installed.
As figure 12 shown, apply a ring of plumbers putty around the back surface of the escutcheon(30). Push the escutcheon
until it is against the wall. Tighten the screw(28) into the bottom of the escutcheon with 2.5mm hex wrench. Remove any
excess putty.
13
Protector cap
Restrictor
Slot
Install the Showerhead
Before installation, install the restrictors if needed. Install the
restrictors into the connectors on the showerhead(33).
Remove the protector caps from the shower arm outlet(34) and
showerhead. Insert the showerhead to the shower arm outlet
as shown.
Insert the pin(35) into the slot. Tighten the screw(36) with 2.5mm
hex wrench(27).
WARNING: Ensure the screw is tightened to avoid the product
falling and personal injury.
4
1418848-2A-C
11
29
17
30
29
31
28
27
32
14
34
33
35
36
27
Protector cap
Install the Handshower
Remove the protector cap from the connector(37)．
Put the screen washer(38) into the shower hose(39).
Connect the handshower(40) and connector(37)
with shower hose. Tighten all the connectors.
NOTE: Don't over tighten.
Install the check valve(41) into the handshower if
needed.
12
30
31
28
27
40
41
38
39
37
5