Aqua Cycle 15 Посібник користувача - Сторінка 2
Переглянути онлайн або завантажити pdf Посібник користувача для Човен. Aqua Cycle 15. Aqua Cycle 15 2 сторінки.
Друкувати сторінкуLUBRICATON, continued
Chain
Use a good quality spray chain lubricant available through a hardware or
motorcycle shop at the beginning of the season and every 6 weeks. The same oil
used for the oil cups may be used on the chain but excess oil may be deposited on
the boards.
*ADJUSTING THE CHAIN*
After approximately 10 hours of use the chain may require it's first adjustment
(tightening). For all model except Aqua Cycle 4x4, loosen the 6 bolts and nuts
holding the rear axle bearings to the side frame rails but do not remove the nuts
from these bolts. Have an assistant grasp the axle from the rear of the boat with
both hands, one on each side of the center frame rail as near to the sprocket as
possible. Avoid bowing the rear axle while pulling the axle to the rear of the boat.
Keep the axle parallel with the rear cross member and tighten the two center bear-
ing mounting bolts and nuts. Be sure the axle is still parallel with the rear cross
member and tighten the right side bearing mounting bolts and nuts. (This is the
bearing on the BOAT'S right side). Release hands from the axle and tighten the
left bearing mounting bolts and nuts. It is important to follow these directions
exactly. Warning. When fully tightened, the chain should be slightly loose, not
taut like a banjo string. Extreme pressure on the axle from over tightening the
chain will cause rear axle and bearing failure. An over loose chain can jump off
the sprockets.
Aqua Cycle 4x4 Chain Adjustment. Follow above instructions to loosen the
rear axle bearings. Also, loosen all 3 middle crank shaft bearings in the same
manner. This will allow both front and back chains to properly adjust when the
rear axle is pulled back. Pull on the rear axle as above. Tighten the 3 middle crank
shaft bearings in the same sequence as the rear bearings. The adjustment slots on
the 2 outside bearings should be equal assuring the crank shaft is parallel to the
rear axle and perpendicular to the chain. Tighten the rear bearings as described
previously.
*SEAT ADJUSTMENT*
The seat may be adjusted to desired position by raising or lowering the adjust-
ment straps in the holes on the sides of the rear seat legs. Move both seat sides
simultaneously to adjust the seat. For maximum forward adjustment, place the
second bolt in the top hole in the rear seat legs.
*CARE OF URETHANE BOARDS*
Clean the boards with a mild detergent and water. A mild spray cleaner such as
409 or Fantastic may also be used. Apply a surface protectant at least once a
year. Suggested protectant brands: Armorall or STP Son of a Gun.
*ALUMINUM CARE*
The aluminum may be cleaned with any good grade of aluminum cleaner as de-
sired. Warning. Be sure your cleaner will not harm other components on the boat,
such as the plated or powder coated metal surfaces, urethane boards, nylon wash-
ers, or bearings.
*NUTS & BOLTS*
Check for loose bolts and nuts at the beginning of each season. The bolts on the
seats and floor boards may loosen due to temperature changes. Warning. Snug
these bolts only! Do not over tighten!
*TRANSPORTING YOUR AQUA CYCLE*
NEVER TRANSPORT THE AQUA CYCLE IN A BACKWARD POSITION.
Damage will occur to the rear of the chain guard mounting and / or the splash
shields if transported backward. The paddle wheel should be secured during
transporting to eliminate excess wear to the chain and bearings. Remove the
Bimini Top before transporting to prevent damage to the bows and brackets.
*SPECIAL CARE FOR USE IN SALT WATER*
Remove your Aqua Cycle from salt or blackish water and rinse thoroughly with
lots of fresh water after each use.
Aqua Cycle is not intended for motorized use.
Aqua Cycle Rear Deck is not intended for passenger use.
Jump or dive from any boat at your own risk.
American Pleasure Products, Inc.
2823 E. Industrial Park Drive
Rose City, MI 48654
Phone: 989-685-2697
Fax:
Email us at
989-685-8484