DEZIT CN 024 100 EIS W Посібник - Сторінка 3

Переглянути онлайн або завантажити pdf Посібник для Електричний обігрівач DEZIT CN 024 100 EIS W. DEZIT CN 024 100 EIS W 16 сторінок. Electric panel heater

Друкувати сторінку

•

Move slightly to the left of the appliance and then lower the down to make

sure that the screws are right at the top of the channels.

BATHROOM OPERATION

•

The panel heater must be installed in accordance with the normal trade

practices and in compliance with the national legislation (EU electricity

directives and regulations concerning special installations and places

of operation including bathrooms, shower cabins HD60364-7-701(IEC

60364-7-701:2006)).

•

In case this panel heater is to be used in a bathroom or other similar room,

the following installation requirements must be observed: the panel

heater is with IP24 protection (water drops protection). Hence it can be

installed in "Volume 2" (see the diagram below) in order to avoid the risk of

the control board (power switch and thermo regulator) being reached by

a person who is in a shower or a bathtub. The minimum distance between

the appliance and a water source should be not less than 1 meter and it

is compulsory the appliance to be wall-mounted! If you do not feel sure

about the installation of this panel heater in a bathroom, we recommend

you to consult a professional electrician.

Note: If the above-mentioned instructions cannot be implemented, it is

recommended to install the appliance in "VOLUME 3".

•

In wet premises the power source must be installed at a height of at least

25 cm above the floor (bathrooms and kitchens).

•

The installation must be equipped with a safety fuse, and the

distance between the fuse contacts in disconnected condition

should be at least 3 mm.

Thank you for choosing DZ 024 panel heater. This is a product providing

heating in winter depending on the consumers' needs for comfortable room

temperature. If operated and taken care of properly in accordance with these

instructions, the appliance will provide you with many years of useful operation.

OPERATION INSTRUCTIONS

ELECTRONIC CONTROL

Operation Modes

"Delayed start" mode LED

/ "Program" mode

"Heating" mode LED

/ Operating heater

ON/OFF Button

Temperature LED

Time LED

"Timer" button for switching on "Delayed start"

or "Program" mode

Turn on the convector, press the switch in position "I" (On)

Time setting

English

The time setting is possible only in Off mode – the current day of the week,

hour and minutes can be set.

To enter the time settings you need to keep simultaneously pressed the "ON/

OFF" and "Timer" buttons. The parameter which is being set blinks on the

display. To select a parameter to set, you need to press briefly the "Timer"

button. To exit the settings, you need to press briefly for a third time the

"Timer" button (after you have set the minutes).

You begin the settings with selecting a day of the week from 1 to 7 depending

on which in order the current day of the week is, and the setting is done by

entering the respective number. The hour and the minutes are displayed

simultaneously and the parameter which is being set is blinking. You can

change the value of the parameter by using the

If no button is presses for 10 seconds, you will exit the settings.

Switching on "Heating" mode

When the panel convector is switched off, the digital display shows the room

temperature and only the Temperature LED is lit. If you press the "On/Off"

button once, you will enable "Heating" mode. A red LED is lit indicating this

mode. The digital display shows the set temperature for about 2 seconds,

and during this time the Temperature LED is not lit. If the room temperature

is lower than the set temperature, the heater will be automatically switched on.

When the heater is on the red LED is permanently lit!

Temperature setting

By pressing either of the buttons

temperature" mode. The display starts flashing and it shows the temperature

which has been set so far. By pressing the buttons you can change the

temperature setting either up or down. If you don't press any button for 5

seconds, the new setting will be stored and the appliance with automatically

go into "Heating" mode. If you keep pressed any of the buttons

more than 0.7 seconds, the value of the set temperature will start increasing or

decreasing by 4 units per second. The temperature setting ranges from 10 to 30

degrees Celsius.

Note: The device shows the temperature around the location of the sensor

and is not a means of accurately measuring the ambient temperature.

"Delayed start" of the panel convector

When the convector is in Off mode, by pressing the "Timer" button you

can enter a specific time after which the appliance will automatically go

in "Heating" mode. This mode is indicated by a blinking yellow LED and

inactive red LED. The digital display will show the room temperature when

the Temperature LED is lit, and it will show the remaining time in hours until

"Heating" mode will be activated and this will be indicated with a lit Timer

LED. Upon activating this mode the yellow LED becomes lit, and the display

starts flashing and showing the entered time in hours until the convector will

be automatically switched on. Initially the display will show 12 hours, and by

using the

any of the buttons

time will start increasing or decreasing by 4 units per second. If you don't press

any button for 5 seconds, or if you press the Timer button, the regulator will

automatically go into "Delayed start" mode. If you enter time 00, this mode will

not be activated. When the "Delayed start" mode is already active, if you press

the "Timer" button again, you can correct the remaining time in both possible

directions. After setting the time, the appliance goes into "Delayed start" mode

with the display showing the temperature and the hours remaining until the

appliance will switch to "Heating" mode. You can exit this mode by pressing the

"On/Off" button. Then the convector will go into "Heating" mode. The "Delayed

start" mode can be set within a range from 01 to 96 hours.

Switching off "Heating" mode

You can exit "Heating" mode by pressing the "On/Off" button. Then the heater

will be switched off, and if it has been on by then, the red LED will go out. The

display will continue showing the room temperature.

"Anti-frost function"

If the room temperature falls below 5 degrees Celsius and the convector is off

(the red LED is not lit, but the mechanical switch is in position "I" (On)

heater will be automatically switched on in order to prevent from freezing.

Entering a temperature correction for the temperature sensor does

not apply to this function.

Enabling and disabling the anti-frost function:

•

this function is enabled by default

•

to disable this function, the convector must be in "Off" mode, when

you press the

show a blinking "ON", and by pressing the

and

you will enter the "Change the set

buttons you can adjust the desired time. If you keep pressed

for more than 0.7 seconds, the value of the set

and "On/Off" button for three seconds the display will

Operation and Storage Manual of Panel Heater

and

buttons.

for

), the

button you will reach the