ALLIED MEDICAL KARMA KM8020 Посібник користувача - Сторінка 7

Переглянути онлайн або завантажити pdf Посібник користувача для Інвалідний візок ALLIED MEDICAL KARMA KM8020. ALLIED MEDICAL KARMA KM8020 9 сторінок.
Також для ALLIED MEDICAL KARMA KM8020: Посібник користувача (9 сторінок)

Друкувати сторінку

Step 2(cont):

down the quick-release mechanism (see fig 3.2).

Step 3:

Slide the backcanes up or down to the desired height

As the backcanes are shifted, the back upholstery will move

Step 3:

Pull the wheel off.

accordingly. There are a number of holes running vertically through

the lower portion of the backcane. These determine how much the

3.2.2

To attach the rear wheel

back height can be raised or lowered.

CAUTION:

For safety reasons, in the highest position the top two bolts must still

Step 1:

Ensure that the brake is in the OFF position.

pass through the square tubing of the frame and the holes running

through the round tubing of the backcane.

Step 2:

Take up the assembled wheel and axle and press the button in the

centre of the axle. This retract the ball bearings that will allow you

Step 4:

Replace the top two bolts on both backcanes.

to push the axle into the wheel bracket that is located on the lower

Replace all washers. Tighten each bolt and nut to a point where firm

rear frame of the wheelchair.

but not crushing the frame.

Step 3:

Remove your thumb from the button on the axle, the ball bearings

Step 5:

Replace the third lower bolt on both backcanes if they have been

should now be visible protruding from the axle at the back of the

removed.

wheel bracket. The wheel should now be secured safely in the frame.

3.3

FITTING AND ADJUSTING A STUMP SUPPORT

3.6

REMOVING THE SEAT OR BACK UPHOLSTERY

3.6.1

To remove the back upholstery

Figure 3.3

Step 3:

To adjust the height, undo the bolt located on the bar underneath the

stump support, lift the support until the desired height is achieved,

replace the bolt and tighten.

Figure 3.6.1

Step 3:

Slightly fold the wheelchair by putting fingers under the middle of the

seat at both front and rear, grasp and give a sharp pull upwards until

3.4

FITTING AND ADJUSTING AN ELEVATING LEGREST

the wheelchair is nearly closed.

Step 4:

Slide the back upholstery off the backcanes.

Step 5:

A tension adjustable or custom back can now be fitted.

Step 6:

Once the new back has been fitted slide rubber grip handles back

onto back canes with a twist and push movement, ensuring they're

placed back in their original position.

Figure 3.4

Page 9

Page 7

Step 1:

Remove the standard footrest by pulling

the release lever and rotate the footrest

until it faces outwards. Lift and remove.

Step 1:

Remove the rubber grip handles. By

slightly heating them with a hairdryer and

Step 2:

Locate the stump support onto the

twisting them whilst pulling them off, will

frame lugs (at about 90 degrees to the

make removing of these easier.

side of the frame) and rotate it inwards

Step 2:

until the support locks into place.

Undo the two screws that are located

underneath the rubber grip handles at the

rear of each back cane (see fig. 3.6.1).

Step 1:

Remove the standard footrest by pulling

the release lever and rotate the footrest

until it faces outwards. Lift and remove.

Step 2:

Locate the elevating legrest onto the

frame lugs (at about 90 degrees to the

side of the frame) and rotate it inwards

until the legrest locks into place.

MINOR WHEELCHAIR ADJUSTMENTS

Step 3:

To adjust the angle of legrest, pull on the lever located underneath

the seat whilst pulling legrest upwards or pushing down. Release

3.1

ADJUSTING ARMREST HEIGHT

lever once desired angle has been achieved to lock legrest securely

Standard flip-back armrest:

into place.

The armrest flips back by pressing the release lever located at the front base of the

To adjust the height of the legrest undo bolt located above footplate, pull or push the

armrest. After you press the release lever (fig 3.1.1), you can you lift the armrest

bar until desired length is achieved, line two holes up and replace bolt and tighten.

backwards.

3.5

ADJUSTING THE BACK HEIGHT

Where to adjust the backcane height

When looking at the rear of the

wheelchair, where the round

backcane tubes meet and enter

the square tubes of the frame,

Figure 3.1.1

three bolts are visible. By removing

these bolts it is possible to adjust

To adjust the height of the armrest, simply pull out the silver bolt located underneath

the height of the back.

the armrest pad (see fig 3.1.3) and hold onto it whilst adjusting the height of the

armrest. Release sliver bolt once desired height is achieved to securely lock armrest

back in place (see fig 3.1.4).

Adjusting the back height

Step 1:

Remove the two top bolts on each side of the backcanes (see arrow

A in fig 3.5 above) - 4 bolts in total

One pair of identical 5mm allen key head bolts are positioned closely

together and towards the top of the square frame tubing. These run

through both the frame and the backcanes. They are attached with a

nut and spaced with small washers.

Figure 3.1.3

Step 2:

Remove the lower bolt on each cane if necessary (see arrow B in

see fig. 3.5 above) - 2 bolts in total

A third bolt is attached through the rear of the swingaway armrests

3.2

QUICK RELEASE REAL WHEELS

and the square frame tube.

3.2.1

To remove rear wheel ensure the brake is off.

This bolt is located directly below the bolts described in Step 1. It is

above and unrelated to the axle block and bolts that attach the wheel

Step 1:

Support the weight of the

to the frame.

wheelchair with one hand by

holding the push handle.

*Only when the backcanes are already set relatively low will this bolt also

have to be removed to adjust the backcane height.

Step 2:

Push the hub cover and hold

Figure 3.1.2

Figure 3.5

Figure 3.1.4

Figure 3.2

Page 6

Page 8