AVS AFM625B Інструкція з експлуатації

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Стелажі та підставки AVS AFM625B. AVS AFM625B 2 сторінки. For lcd, plasma, and led displays

Друкувати сторінку

FULL-MOTION WALL MOUNT

FOR LCD, PLASMA, and LED DISPLAYS

INSTRUCTION MANUAL

Thank you for choosing the AVS AFM625B. Before beginning installation, please

check all parts are included and undamaged. For any parts enquiries, please

contact AV Supply Group Ltd on (09) 274 9172 or email to [email protected]

SPECIFICATIONS

Model: AFM625B

Display Size: 37" to 80"

Maximum Load: 68 kg (150 lbs)

Mounting Pattern: 600 mm x 400 mm (23.6" x 15.7") max

Tilt Range: 3° up to 12° down

Pan/Swivel Range: up to 180°

Proﬁle: 8 cm to 65 cm (3.1" to 25.6")

BOX CONTENTS

Mount (x1)

Instruction Manual (x1)

Mount Arm (x2)

Hardware Kit (x1)

IMPORTANT SAFETY INSTRUCTIONS

PRODUCT CARE: Periodically clean your mount with a dry

cloth. Inspect all screws and hardware at regular intervals

to ensure that no connections have become loose over

time. Re-tighten as needed.

CAUTION: Do not use this product for any purpose not

explicitly speciﬁed by AVS. Improper installation may cause

property damage or personal injury. If you do not

understand these directions, or have doubts about the

safety of the installation, contact AVS Customer Service or

call a qualiﬁed contractor. AVS is not responsible for damage

or injury caused by incorrect mounting, assembly, or use.

WARNING! This product contains small items that could

be a choking hazard if swallowed. Keep these items away

from young children!

The wall or mounting surface must be capable of

supporting the combined weight of the mount and the

display; if not, the structure must be reinforced.

Locate pipes, wires, or any other hazards in the wall where

you wish to install.

Safety gear and proper tools must be used. Failure to do so

can result in injury or damage.

Follow all instructions and recommendations regarding

adequate ventilation and suitable locations for mounting

your display. Consult the owner's manual for your

particular display for more information.

AV Supply Group (AVS) intend to make this manual

accurate and complete. However, AVS makes no claim that

the information contained herein covers all details,

conditions, or variations. Nor does it provide for every

possible contingency in connection with the installation or

use of this product. The information contained in this

document is subject to change without notice or

obligation of any kind. AVS makes no representation of

warranty, expressed or implied, regarding the information

contained herein. AVS assumes no responsibility for

accuracy, completeness or suﬃciency of the information

contained in this document.

TOOLS REQUIRED

Phillips Head Screw Driver

Ratchet or Driver with a 1/2" Socket

Electric or Portable Drill

1/4" Drill Bit and Stud Finder for Drywall Installation

3/8" Masonry Bit for Concrete Installation

Level

HARDWARE KIT

(A)

Lag Bolt (x4) (x4)

(F)

M6 Washer (x4)

(B)

Washer (x4)

(G)

M8 x 12 Screw (x4)

Concrete Anchor (x4)

(H) M8 x 30 Screw (x4)

(C)

M6 x 12 Screw (x4)

(I) M8 Washer (x4)

(D)

M6 x 30 Screw (x4)

(J) Spacer (x8)

(E)

INSTALLATION

Part 1A – Mounting to the Wall (Drywall)

IMPORTANT! The mount must be secured to at least two

wood studs no less than 16" apart. The studs must be capable

of supporting the combined weight of the mount and

display.

Use a high quality stud ﬁnder to locate two studs on the

wall where you wish to install your mount. Mark both

edges of each stud to help

identify the exact center.

NOTE: Use the center of each

stud to avoid cracking or splitting

the wood.

Carefully remove the plastic

covers from the mount as shown

(see Fig. 1).

Place the mount against the wall

over the marked studs with the

arrow on the mount pointing up.

Make sure it is level.

While another person holds the

mount in place, mark four

locations (two per stud) for

securing the mount to the wall

(see Fig. 2).

Set the mount aside and drill a

1/4" pilot hole at each marked

location.

Attach the mount to the wall with the arrow pointing up

using the lag bolts (A) and washers (B) provided (see Fig. 3).

Do not release the mount until all bolts are secure. Ensure

that the mount remains level.

Part 1B – Mounting to the Wall (Concrete)

IMPORTANT! For safety reasons, the concrete wall must be

capable of supporting the combined weight of the mount

and the display.

Fig. 1

Fig. 2

Fig. 3