DH Lifelabs AquaSolvo AAHE-120WH03Pro Інструкція з експлуатації - Сторінка 5
Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Лабораторне обладнання DH Lifelabs AquaSolvo AAHE-120WH03Pro. DH Lifelabs AquaSolvo AAHE-120WH03Pro 8 сторінок. Commercial eco air sterilizer
Друкувати сторінку
Unpacking and Setup
1. Remove the unit from the box and check
that all the items shown in Figure 1 are
included. It is a good idea to retain the
packaging for storing the unit or in the
event it must be shipped back for service.
2. Locate the unit on a flat, solid surface in
proximity to an AC electrical outlet.
3. Using the key, unlock and open the side
panel.
4. Remove poly foams packed inside the
machine.
CAUTION: The AC adapter must be plugged
in using the 3-prong grounded plug.
5. Connect the AC adapter to the unit, and
route the power cord to the outlet, but do
not plug it in yet. Make sure that the power
cord is out of the way and does not pose
a tripping hazard, and is out of reach of
children and pets.
Congratulations! You are now ready to
enjoy clean safe air using the AquaSolvo
Commercial Eco Air Sterilizer.
Moving the Sterilizer
The Sterilizer is equipped with four swivel
casters to make it easier to move around. To
avoid any problems when moving the Sterilizer,
observe these precautions:
1. Unplug the Air Sterilizer before moving it.
2. Make sure that the side panel on the Space
Sterilizer is securely closed.
3. Move the machine by holding onto the
handle on the front of the machine with
hands for assistance.
4. To avoid spilling any water, move the
Sterilizer carefully. Immediately clean up
any spills.
5. The two front casters have a safety lock
that will prevent unwanted movement.
5
Initial Startup
When the Sterilizer is first powered up, you
will hear the startup chime (do-re-mi) and
the Room Size Selection button will flash,
prompting you to select the appropriate room
size. To select a room size, press the button
repeatedly to cycle through the available
options (500, 700, 900, 1100, and 1300 square
feet). If no selection is made within 30 seconds
the Sterilizer will default to 900 square feet.
After a size is chosen, the Sterilizer will remain
in that room size mode whenever it is powered
on, until it is changed by the user.
Preparation for Operation
1. Using the key, unlock and open the side
panel. The machine will shut down.
2. Remove the two water containers from the
water tray.
NOTE: Avoid touching the cold evaporation
units to minimize possible contamination.
Do not use purified water or distilled water.
3. Fill each of the water container with tap
water in full (3500 ml/118.35oz. of water).
Add 2 scoops of non-iodized salt to each
of the water containers.
4. Place the water containers back into the
water tray.
5. Close and lock the side panel.
6. Plug the AC power cord into an outlet.
Operation Instructions
The Control Panel
Operation of the unit is controlled by buttons on the Control Panel as shown in Figure 2.
Figure 2. Control Panel
Icon
Description
Digital Display .
Indicates the current humidity level in the room. On either side of the display
are the Salt Level indicator, the Cold Evaporation Filter Replacement indicator,
the Water Level indicator, the HEPA Filter Replacement indicator.
Power ON/OFF Button .
Controls operation of the unit. Pressing the button turns the unit ON or OFF.
Any time the unit is turned on in the future it will start up the same operating
mode it was in when last operated. The HOCl function is turned on by default.
Filter Reset Button .
After changing either the Cold Evaporation Filter or the 2-in-1 HEPA Filter,
press and hold this button for 3 seconds to reset the filter life countdown.
Fan Speed Button .
Use this button to adjust the fan speed, toggling through the 1-2-3 fan speeds.
An indicator corresponding to the selected fan speed will illuminate.
Timer Button .
The Timer Button allows you to select how long the machine will run before it
automatically shuts off. There are three pre-set times: 4, 8 and 12 hours. Press
the icon toggle through the options (4H-8H-12H-None). Once selected, an
internal timer controls operation of the unit for the selected duration. Once
the timer expires, the unit shuts down and enters the standby mode.
Sterilize Button .
The light remains on when the machine is on and flash when electrolysis is
working to process HOCl.
You can turn the sterilization function off, then it will work as a purifier.
Rooom Size Selection Button .
Press this button to select the appropriate room size for the Sterilizer
operation. The generating concentration of HOCl will be adjusted to match
the room size selected. The available options are 500, 700, 900, 1100, and 1300
square feet. If no size is selected within 30 seconds of power on, the Sterilizer
will default to 900 square feet.
6