Dell PowerVault LTO-3-060 Посібник користувача - Сторінка 30
Переглянути онлайн або завантажити pdf Посібник користувача для Зберігання Dell PowerVault LTO-3-060. Dell PowerVault LTO-3-060 37 сторінок. Powervault tape systems
Також для Dell PowerVault LTO-3-060: Налаштування (2 сторінок), Посібник (28 сторінок)
0x2E. TapeAlert flags may appear as messages on the application screen or in the application error logs.
TapeAlert Flags
Table 5 lists the TapeAlert flags that are supported by the Dell PowerVault LTO3-060 Tape Drive.
Table 5. TapeAlert Flags and Descriptions
Flag
Flag
Parameter
Number
(in hex)
3
03h
Hard error
4
04h
Media
5
05h
Read failure
6
06h
Write failure
8
08h
Not data grade
9
09h
Write protect
10
0Ah
No removal
11
0Bh
Cleaning media
12
0Ch
Unsupported format
Cartridge memory
15
0Fh
chip failure
16
10h
Forced eject
Tape directory
18
12h
corrupted in the
cartridge memory
20
14h
Clean now
21
15h
Clean periodic
22
16h
Expired clean
23
17h
Invalid cleaning tape
30
1Eh
Hardware A
TapeAlert Flags Supported by the Tape Drive
Flag
Description
Set for any unrecoverable read, write, or
positioning error. (This flag is set in
conjunction with flags 4, 5, or 6.)
Set for any unrecoverable read, write, or
positioning error that is due to a faulty tape
cartridge.
Set for any unrecoverable read error where
isolation is uncertain and failure could be
due to a faulty tape cartridge or to faulty
drive hardware.
Set for any unrecoverable write or
positioning error where isolation is uncertain
and failure could be due to a faulty tape
cartridge or to faulty drive hardware.
Set when severe servo errors occur while
loading a tape cartridge.
Set when the tape drive detects that the
tape cartridge is write-protected.
Set when the tape drive receives an
UNLOAD command after the system
prevented the tape cartridge from being
removed.
Set when you load a cleaning cartridge into
the drive.
Set when you load an unsupported
cartridge type into the drive or when the
cartridge format has been corrupted.
Set when a cartridge memory (CM) failure
is detected on the loaded tape cartridge.
Set when you manually unload the tape
cartridge while the drive was reading or
writing.
Set when the drive detects that the tape
directory in the cartridge memory has been
corrupted.
Set when the tape drive detects that it needs
cleaning.
Set when the drive detects that it needs
routine cleaning.
Set when the tape drive detects a cleaning
cartridge that has expired.
Set when the drive expects a cleaning
cartridge and the loaded cartridge is not a
cleaning cartridge.
Set when a hardware failure occurs that
requires that you reset the tape drive to
recover.
Action Required
See the Action Required column for Flag 4, 5, or 6 in this table.
The Cartridge is defective. Contact Dell technical support.
If Flag 4 is also set, the cartridge is defective. Contact Dell technical
support. If Flag 4 is not set, see
"General
troubleshooting section of this manual.
If Flag 9 is also set, make sure that the write-protect switch is set so
that data can be written to the tape (see
Switch"). If Flag 4 is also set, the cartridge is defective. Replace the
tape cartridge. If Flag 4 is not set, see "
troubleshooting section of this manual.
Replace the tape cartridge. If this error occurs with multiple tapes,
see
"General
Guidelines" in the troubleshooting section of this
manual.
Make sure that the cartridge's write-protect switch is set so that the
tape drive can write data to the tape
Switch
section.
Refer to the documentation for your system's operating system.
No action required.
Use a supported tape cartridge.
Replace the cartridge. If this error occurs on multiple tapes, see
"General
Guidelines" in the troubleshooting section of this manual.
No action required.
Reread all data from the tape to rebuild the tape directory.
Clean the tape drive. See the
"Cleaning the Tape
section."
Clean the tape drive as soon as possible. The drive can continue to
operate, but you should clean the drive soon. See the
Tape Mechanism
section."
Replace the cleaning cartridge.
Use a valid cleaning cartridge.
Reset the tape drive. See
"Resetting the
does not recover the error, see
"General
troubleshooting section of this manual.
Guidelines" in the
"Setting the Write-Protect
General
Guidelines" in the
"Setting the Write-Protect
Mechanism"
"Cleaning the
drive". If resetting the drive
Guidelines" in the