Dell S6010-ON Примітки до випуску прошивки - Сторінка 10
Переглянути онлайн або завантажити pdf Примітки до випуску прошивки для Перемикач Dell S6010-ON. Dell S6010-ON 12 сторінок.
Також для Dell S6010-ON: Посібник з монтажу (46 сторінок)
Друкувати сторінку
root@OS10:~# /mnt/onie-boot/onie/tools/bin/onie-fwpkg
** Pending firmware update information:
Name
======== ====+====
fw-updater.bin | x.xx.x.x-xx |
=============+==========+==========+==============+====================
For more detailed information run: onie-fwpkg show-pending <update_name>
root@OS10:~#
10. Set next boot to ONIE update mode.
root@OS10:~# os10-image -o update
WARNING: ONIE update requested
Are you sure (y/N)? y
Success setting boot mode to ONIE update
Reboot required to take effect
root@OS10:~#
11. Reboot your switch to enter ONIE update mode and start the firmware update.
Optionally, to set the next boot to ONIE mode, use the ONIE:/# onie-boot-mode -o update command.
Verify firmware update
After you have updated the firmware, verify that all components—BIOS and CPLD, are running the correct version.
● To check the BIOS version, use the dmidecode -2 system-version command in ONIE. The BIOS version also displays
during switch bootup. You can run this command from either ONIE or the DIAG OS.
● To check the CPLD version, use the cpldupgradetool --cpldver command.
Firmware update staging from ONIE
1. Boot into ONIE Rescue or Update mode.
If you boot into Update mode, stop discovery using the onie-discovery-stop command.
2. Copy the fw-updater image from the host to the target.
onie-fwpkg command with 'add' option would queue the firmware update.
onie-fwpkg add <fw_updater.bin>
3. Boot back to ONIE update mode if you previously booted to Rescue mode.
After you boot into ONIE Update mode, the ONIE firmware updates infrastructure, locates the firmware update archive, and
proceeds to update the components.
If you were previously in ONIE Update mode and stopped discovery using the onie-discovery-stop command, restart
discovery using the onie-discovery-start command. This command causes the ONIE firmware updater infrastructure to
locate the firmware updater binary image and proceed with the firmware update.
The following is a list of ONIE staging command options:
ONIE:/mnt/onie-boot # onie-fwpkg purge
Removing all pending firmware updates (
y/N)? y Purging all pending firmware updates. ONIE:/mnt/onie-boot #
ONIE:/mnt/onie-boot # onie-fwpkg
** Pending firmware update information:
No pending firmware updates present.
ONIE:/mnt/onie-boot #
ONIE:/mnt/onie-boot # wget http://xx.xx.x.xxx//tftpboot/users/<name>/<platform>/FWUPG
RD/onie-firmware-x86_64-dell_<platform>_c2338-r0.x.x.x.x.bin
Connecting to xx.xx.x.xxx (xx.xx.x.xxx:xx)
onie-firmware-x86_64 100% |*******************************| 12521k 0:00:00 ETA
ONIE:/mnt/onie-boot #
ONIE:/mnt/onie-boot # onie-fwpkg add onie-firmware-x86_64-dell_<platform>_c2338-r0x.x.x.x.bin
Staging firmware update: onie-firmware-x86_64-dell_<platform>_c2338-r0.x.x.x.x.bin
ONIE:/mnt/onie-boot #
10
| Version
| Attempts
=====+==========+==============+====================
|Size (Bytes)
0
|
19314551
| Date
| 2018-02-17 03:19:35