AVYCON AVC-PHN61FLT Посібник із швидкого старту
Переглянути онлайн або завантажити pdf Посібник із швидкого старту для Камера спостереження AVYCON AVC-PHN61FLT. AVYCON AVC-PHN61FLT 2 сторінки. Hd network fisheye camera
Друкувати сторінку
HD Network Fisheye Camera
Quick Start Guide
Please read this instruction carefully and preserve it for further reference. All the examples and pictures used
here are for reference only. There may be several technically incorrect places or printing errors in this manual.
The update information will be added into the new version of this manual. The contents of this manual are
subject to change without notice.
1. Warning and Caution
■ If the product does not work properly, please contact your dealer or the nearest
service center. Never attempt to disassemble the camera yourself. (We shall not
be responsible for any problems caused by unauthorized repair or maintenance.)
■ Keep away from liquid while in use.
■ In the use of the product, you must be strict compliance with the electrical safety
regulations of the nation and region. When the product is mounted on wall or
ceiling, the camera shall be firmly fixed.
■ Do not use camera beyond specified voltage range.
■ Do not drop the camera or subject it to physical shock.
■ Avoid touching the camera lens.
■ If cleaning is necessary, please use clean cloth to wipe it gently.
■ Do not aim the camera at the sun or extra bright place.
■ Do not place the camera in extremely hot, cold (the operating temperature shall
be -20˚C ~ 50˚C), dusty or damp locations, and do not expose it to high
electromagnetism radiation.
■ To avoid heat accumulation, good ventilation is required for operating
environment.
■ A few parts of the device shall be replaced regularly according to their average
enduring time. Regular checking is recommended for all users.
2. Package
Camera
Quick Start Guide
3 Tapping screws PA 4 x 25
CD
Screwdriver
Drill template
3. Overview
Network Interface
1
2
3
HP Audio Output
4
5
Alarm Input / Output
* If the PoE switch is used to power the camera, DC12V power supply is not required.
□
• Alarm Connection
Alarm Input: Join the grounding ends of the sensor and the camera and
then connect the signal cable of the sensor to the alarm input port (ALM-INA)
of the camera.
Alarm Output: Loosen the screws in the alarm output port. Then insert the
signal wires of the alarm output devices into the port of COM and OPEN
separately. Finally tighten the screws. Some of the external alarm output
devices need the power supply.
□
• Connecting Network Cable
① Loosen the nut from the main element.
Plastic Plug x 3
② Run the network cable (without RJ 45 connector) through the both elements
Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the nut and
the main cover.
1
2
3
4
5
6
7
8
9
6
RS485
MIC IN
7
DC12V Power Supply
8
SD Card Slot
9
Video Output
Reset
ALM-COM
ALM-OPEN
ALM-INA
ALM-GND
RS485T+
RS485T-
DC12V
1
2
4. Installation
Please install and use the camera in the dry environment. You'd better install
back the cover less than 4 hours after removing it.
• Install SD Card
① Remove the fixed ring from the gap of the camera.
Fixed Ring
Gap
② Loosen the screws of the cover of the SD card and then insert the SD card.
After that, install the cover back.
• Install Camera
Before installation, please make sure that the wall is strong enough to
withstand 3 times the weight of the camera.
① Remove the fixed ring from the gap of the camera (see Install SD Card ①).
② Drill the screw holes and the cable hole on the wall according to the drill
template.
84mm
97mm
3
Ø130mm
Ø4.5mm