EarthWise CCS30008 Посібник оператора - Сторінка 8
Переглянути онлайн або завантажити pdf Посібник оператора для Бензопила. EarthWise CCS30008. EarthWise CCS30008 11 сторінок. Cordless 18 volt chain saw
Друкувати сторінку
MAINTENANCE
[
I
If you drop
the
chain saw. carefully inspect it for damage. If the
blade is bent, housing cracked. or handles broken or
if
you see any
other condition that may affect the saw's operation, contact your
local Authorized Service Center for repairs before putting it back
into use,
Make
sure the battery is detached from
then use only mild
soap and a damp cloth to clean the tool. Never
any liquid get
inside the tool: never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY.
repairs, maintenance and adjustment should be parformed by an
authOrized service center or other qualified service organization,
always using
identical replacement parts.
CAUTION:
Do
not at any time let brake fluids, gasoline, petroleum
based products, panetrating oiis, etc.. come in contact with plastiC
parts. They contain chemicals that can damage, weaken or
destroy plastic.
Ensure that the plastiC blade cover is in placa when stonng.
Fertilizers and other garden chemicals contain agents which
greatly accelerate the corrosion of metals Do not store the tool on
or adjacent to fertilizers or chemicals.
For smoot!1 and fast cutting, chain
needs
to ba maintained proparly.
The chaln requires sharpening when the WQod chips are small and
powdery, the Chain must be fOrced through the wood during cut
ting,
or
the chain cuts
to one
side. Refer to instructions earlier in
this manuat for instructions on properly sharpening the chain.
LUBRICATION SYSTEM
The chain is
a~tomatiOOlly
lubricated.
Use only new chain oil specifica!ly formulated for chainsaws.
Never use wasted oil, low quality oil, or insufficient oil. This could
damage the
p~mp;
the bar and the chain which may result in serious
injury.
oil level bafore each work session, refill if lass than
Yo
full.
If the lubrication system does not work properly, check if the oil filter
and all oil-ways afe clean and frea from obstrucUons. If it is still not
working, contact an authorised service center.
GUIDE BAR MAINTENANCE
When
the guide bar shows signs of wear, raverse it on the saw to
distribute Ihe wear for maXimum bar life. The bar should be cleaned
every day of use and chacked for wear and damage.
Feathering or burring
of
the bar rails is a normal process of bar wear.
Such faults should ba smoothed with a file as soon as they occur.
A bar with any
of
the following faults should be replaced.
- Wear inside
the
bar rails which
penmils
the chain to layover sideways.
- Bent guide bar
- Cracked or broken rails
- Spread rails
In addition, guide bars with a sprocket at their tip must ba lubricated
weekly with
a
grease syringe
to
extend the guide bar Ufe. Using
a
grease syringe, lubricate weekly in the lubricating hole.
Tum the guide bar and check that the lubrication holes and chain
groove are free from impurities.
Problem
- Unit does not run
Bar and chain running hot
and smoking
~
Motor runs but Chain is
not rotating
TROUBLESHOOTING
POSSible Cause
Possible Solution
- Baltery not making contact
- Check battery is fully inserted
- Lock off not fully operated
- CheCK that lock off is fully forward prior 10
- Battery not installed properly
moving trigger
- Battery not Qharged
- Check battery installation
Check batten} charging requirements
- Check tension for over-tight condition
- Adjust chain tension
- Chain oit tank empty
- Fill tank with chain oil
Chain tension too tight
- Check guide bar and chain for damage
- Adjust chain tension
- Replace damaged bar and chain with identical
replacement parts or contact an authorized
sef'lice center for repair.
CALL US FIRST II
Call us first
with
questions about operating or maintaining your chain
saw
aI1.800.313.5111
between 7:30 a.m. -
4:30
p.m. Eastern
Standard Time, or send [email protected].