EarthWise NVPS42110 Посібник оператора - Сторінка 11
Переглянути онлайн або завантажити pdf Посібник оператора для Бензопила. EarthWise NVPS42110. EarthWise NVPS42110 14 сторінок. 18 volt, cordless convertible 2 in 1 pole saw / chain saw
Друкувати сторінкуBEFORE USING: Fill oil well with new quality bar and chain
oil. Unused SAE 30 weight motor oil may be substituted.
If you drop the saw, carefully inspect it for damage. If the
blade is bent, housing cracked, or handles broken or if you
see any other condition that may affect the saw's operation,
call our customer service help line at 1-800-313-5111 for
assistance.
Remove the battery pack from the pole saw, then use only
mild soap and a damp cloth to clean the tool. Never let any
liquid get inside the tool; never immerse any part of the tool
into a liquid.
After cleaning, apply a light coat of oil to the chain and guide
bar to prevent rusting.
IMPORTANT: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment should be performed by
a qualified individual always using identical replacement
parts.
CAUTION: Do not at any time let brake fluids, gasoline,
petroleum based products, penetrating oils, etc., come in
contact with plastic parts. They contain chemicals that can
damage, weaken or destroy plastic.
Ensure that the plastic bar cover is in place when storing.
Fertilizers and other garden chemicals contain agents which
greatly accelerate the corrosion of metals. Do not store the
tool on or adjacent to fertilizers or chemicals.
For smooth and fast cutting, chain needs to be maintained
properly. The chain requires sharpening when the wood chips
are small and powdery, the chain must be forced through the
wood during cutting, or the chain cuts to one side. Refer to
instructions earlier in this manual for instructions on properly
sharpening the chain.
Problem
Unit does not run
-
Bar and chain running hot and
-
smoking
- Motor runs but chain is not rotating
MAINTENANCE
TROUBLESHOOTING
Possible Cause
- Battery not making contact
- Lock off not fully operated
- Battery not installed properly
- Battery not charged
- Check tension for over-tight condition
- Chain oil tank empty
- Chain installed backwards
Chain tension too tight
-
- Check guide bar and chain for damage
CALL US FIRST !!
Call us first with questions about operating or maintaining your chain
saw at 1.800.313.5111 between 7:30 a.m. – 4:30 p.m. Eastern
Standard Time, or send emails to [email protected].
LUBRICATION SYSTEM
The chain is automatically lubricated.
Use only new bar and chain oil or unused SAE 30 weight
motor oil may be substituted. Never use wasted oil, low
quality oil, or insufficient oil. This could damage the pump, the
bar and the chain which may result in serious personal injury.
Check oil level before each work session, refill if less than 1/4
full.
If the lubrication system does not work properly, check the oil
filter and that all oil-ways are clean and free from obstructions.
If it is still not working, call our customer service help line at
1-800-313-5111 for assistance.
GUIDE BAR MAINTENANCE
When the guide bar shows signs of wear, reverse it on the
saw to distribute the wear for maximum bar life. The bar
should be cleaned every day of use and checked for wear and
damage.
Feathering or burring of the bar rails is a normal process of
bar wear. Such faults should be smoothed with a file as soon
as they occur.
A bar with any of the following faults should be replaced:
- Wear inside the bar rails which permits the chain to lay
over sideways.
- Bent guide bar
- Cracked or broken rails
- Spread rails
In addition, guide bars with a sprocket at their tip must be
lubricated weekly with a grease syringe to extend the guide
bar life. Using a grease syringe, lubricate weekly in the
lubricating hole.
Turn the guide bar and check that the lubrication holes and
chain groove are free from impurities.
- Check battery is fully inserted
- Check that lock off is fully pressed prior to moving trigger
- Check battery installation
- Check battery charging requirements
- Adjust chain tension
- Fill tank with chain oil
- Reverse chain so that cutters face the right direction
- Adjust chain tension
- Replace damaged bar and chain with identical replacement
parts.
11
Possible Solution