Earthwise Electronics ComfortZone Посібник користувача - Сторінка 12
Переглянути онлайн або завантажити pdf Посібник користувача для Система опалення Earthwise Electronics ComfortZone. Earthwise Electronics ComfortZone 14 сторінок. Therapeutic infrared heating systems
Друкувати сторінку
Page 11
Operating Instructions at a Glance:
Turning Power On
Press the POWER button on the left side of the Control Panel. The heater's
quartz heating elements will light up inside the heater. After a few minutes,
once the air within the heater is warm, the heater fan (some models have 2)
will begin to operate.
Turning Power Off
Press the POWER button located on the left side of the Control Panel. The
sound of the heater fan will continue until the heat has been completely
vented, thus protecting the unit and preventing waste by cycling the
remaining heat into the room. (NOTE: DO NOT unplug the heater until the sound
of the fan has stopped. Doing so may cause damage to the unit.)
Setting the Temperature
This feature allows you to set the temperature your heater will maintain.
1. Press the temperature (TEMP) button on the Control Panel; the SET TEMP
indicator will illuminate and the temperature display will flash.
2. Use the UP and DOWN buttons to select the temperature and press enter.
3. The SET TEMP light will turn off, and the temperature is now set.
Setting the Timer
This feature allows you to set a future time for the heater to turn itself on. For
example, if you set the time for 1 hour, the heater will turn on in 1 hour.
1. Turn the power off (heater must be powered off to use the timer feature).
2. Press the TIME button on the Control Panel—the two zeros to the right will
flash (:00), indicating 0 minutes have been set, and the DELAY START
indicator will illuminate.
3. Press the UP or DOWN button to select desired number of minutes (up to 59
minutes) that you would like the heater to wait to turn itself on.
4. P ress the ENTER button—the two zero buttons to the left will flash (00:),
indicating 0 hours have been set.
5. Press the UP or DOWN button to the desired number of hours (up to 24
hours), and then press the ENTER button.
6. D ELAY START indicator will flash until the unit comes on after waiting the
period of time you have set.
7. To cancel the timer, press the power button and the timer will stop.
Switching Between Fahrenheit & Celsius
Press the DOWN & ENTER buttons simultaneously and hold for about 3
seconds. The display will update automatically.
Customer/Warranty Service: (866) 446-2864
Troubleshooting Your ComfortZone
Problem
Solution
Make sure the electrostatic filter is clean (see
Maintenance).
The heater's airflow has
Check front grill and look behind rear air intake
been reduced.
for any objects that could obstruct airflow.
If the heater's airflow is still diminished or has
stopped, please call Customer Support.
This is a normal function of the heater. DO NOT
The heater stays on after I
unplug the heater until you no longer hear the
push the Power button to
fan running. During this time, the heater is
turn it off.
cooling down.
This is part of the heater's normal operation.
After a period of inactivity, the heater will enter
into a "screen saver" mode to conserve power.
The heater's display is
This will not affect the heater's operation.
showing a line of dots.
When any function key is pressed, the heater's
display will reappear.
Heater thermostat
Call your Dealer to obtain programming
temperature does not
instructions for matching your ComfortZone
match wall thermostat
thermostat settings with your existing wall
temperature
thermostat.
Test the outlet to make sure there is power
available and then check the heater display for
The heater will not turn on.
the flashing TIME DELAY light. Press the
POWER button to turn off the timer and
resume normal operation of the heater.
Page 16
™
©2008 EarthWise Electronics, Inc