Dialight ProSite Floodlight UL 1598A Інструкція з монтажу та експлуатації - Сторінка 5

Переглянути онлайн або завантажити pdf Інструкція з монтажу та експлуатації для Прожектор Dialight ProSite Floodlight UL 1598A. Dialight ProSite Floodlight UL 1598A 10 сторінок.

Друкувати сторінку

Slip Fitter Models: F1U******S****

Make proper connections inside the junction

base of the slip fitter and tuck any excess

wiring into the junction base. Assure none of

the wiring can be pinched when replacing

cover.

Install the cover and tighten the hardware

using the recommended torque to assure a

proper seal.

Torque: 1 in-lb [1.4 N-m]

Mast Arm Models: F2U******T****

Open the mast arm cover by loosening the

two captive 10-32 screws and pulling the

cover open. Loosen the four ½-13 bolts most

of the way to allow the pole to slide into the

housing.

Slide the fixture onto the pole at desired

incline. The middle "step" represents 0⁰ tilt.

The

other

steps

represent

respectively. Adjust to desired step as

needed. Tighten the four ½-13 bolts evenly

around the pole. Ensure that the clamp plate

remains parallel to the bottom of the mast

arm housing. A two axis bubble level is

included for mounting convenience.

Torque to 29-31 ft-lbs [39.3-42.1 N-m]

4x 1/2 -13 bolts

Feed mains cable through supplied cable

gland and into wire box.

Torque cable gland to 45-55in-lbs[5.2-6.2N-m]

After the fixture has been mounted, snap the

access cover closed and tighten the two 10-

32 captive screws to 30 in-lbs [3.4 N-m]

Note: If the access cover interferes with

mounting the fixture, press on the hinges

towards the top/front of the fixture. The cover

is spring-loaded and will snap out of place. To

reinstall after mounting, align the hinges on

the inclined springs and push towards the

back of the fixture. Cover should snap back

into place.

9100FLM000900 REV E

Page 5 of 10

ProSite Floodlight for UL 1598/1598A

"W" bracket orientation

NOTE: The bracket that is factory installed is

suitable for 2" NPS poles. For 1.25" NPS or 1.5"

NPS poles, the second "W" shaped bracket

found in the box should be used by replacing

the factory-installed bracket. Be sure to reuse

the four ½-13 bolts, flat washers, and lock

washers.

Asymmetric Wide Throw Models:

F2UNJ*********

After installation, remove the 4x rubber optic

protectors and 4x 10-32 screws. These can

then be discarded.

+/-5⁰

tilt

WARNING: The optic features on Asymmetric

Wide Throw models may be very sharp.

Appropriate actions should be taken when

handling the unit in order to prevent injury.

Damage to these sharp optical features will

result in degradation of the light pattern.

Electrical Connections

Bracket Models: F*U******(E/F)****

The terminal block is suitable for multi-

stranded or single core wires. The parameters

can be found in Technical Data.

Push Down Terminal Models: F*U********V**

Push down at the 'cross point', insert wire, and

release.

Conductor Range

0.5-4 mm² [20-12 AWG]

Screw Down Terminal Models: F*U********U**

For input power terminal block, loosen

terminal screw, insert wire, and tighten screw.

Conductor Range

0.5-6 mm² [20-10 AWG]

For dimming & Dali lines, push down at the

'cross point', insert wire, and release.

Conductor Range

0.5-4 mm² [20-12 AWG]

Slip Fitter Models: F1U******S****

All slip fitter models contain lever nut

connectors inside the junction base to make

appropriate connections.

Conductor Range

0.5-4 mm² [20-12 AWG]

Single Phase Connections

The connections are marked on the terminal

block or on a label and are presented in the

table below.

SYMBOL

DIM +

DIM -

DALI

0-10 VDC Dimming (If Applicable)

Dimming is controlled by means of a 0-10

VDC signal (to be provided by the installer) to

control the level of dimming. At 10 volts, the

output of the unit is 100%; at 0 volts, the output

will shut off. The DC dimming voltage should

not exceed 15 VDC. Increasing the voltage

from 10 VDC to 15 VDC will not result in

Strip Length

additional light output.

9 mm [0.35 in.]

WARNING: Never connect the dimming wires

to the Hot/Live or Neutral supply wires.

Dialight, 1501 Route 34 South, Farmingdale, NJ, USA 07727

Tel: +1 732 919 3119 Fax: +1 732 751 5778

Strip Length

10 mm [0.39 in.]

Strip Length

9 mm [0.35 in.]

Strip Length

9 mm [0.35 in.]

COLOR

CONNECTION

120-277VAC

GREEN/

EARTH/

YELLOW

GROUND

WHITE

NEUTRAL

BLACK

LIVE

120-250VDC

GREEN/

EARTH/

YELLOW

GROUND

WHITE

BLACK

347-480VAC

GREEN/

EARTH/

YELLOW

GROUND

RED

LIVE 2

BLACK

LIVE 1

CONTROLS

VIOLET

DIMMING +

GREY

DIMMING -

ORANGE

DALI

OR YELLOW