Dialight SafeSite ATEX Інструкція з експлуатації Посібник з експлуатації - Сторінка 5

Переглянути онлайн або завантажити pdf Інструкція з експлуатації Посібник з експлуатації для Ліхтар Dialight SafeSite ATEX. Dialight SafeSite ATEX 7 сторінок. Stainless steel led linear luminaire for hazardous areas

Друкувати сторінку

Safety Instruction:

The installation, operation and

maintenance must be carried out by

an electrician suitably trained in

hazardous areas with knowledge of

increased safety explosion protection

IEC 60079-14.

• The technical data indicated on the

LED luminaires are to be observed.

• Changes of the design or

modifications to the LED luminaire

are not permitted

• Observe the national electrical safety

rules and regulations during

installation.

• No user serviceable parts inside.

• No field replaceable parts.

Technical Data:

Category of Application:

32W:

Ex e mb IIC T4 Gb

Ex tb IIIC T135°C Db

II 2GD

64W

Ex e mb IIC T4 Gb

Ex tb IIIC T135°C Db

II 2GD

IECEx / ATEX:

SIRA 12ATEX3217X

IECEx SIR 12.0093X

Rated Input

Voltage:

100-277 VAC 50/60 Hz

Rated Input Current:

32W:

175mA at 230V AC

350mA at 110V AC

64W:

350mA at 230V AC

700mA at 110V AC

Inrush Current

@230VAC

32W:

1A for 6ms

64W:

6A for 50μs

Operating Temp. -20°C to +60°C

Housing:

Marine Grade 316

Stainless Steel IP66/67

Dimensions:

See diagram page

Cable Entries:

Standard 2 OFF M20 x 1.5mm

(M25 x 1.5mm optional)

Terminal block:

Standard: 4-way, max. 4mm²

5 wire thru: 7-way, max. 4mm²

Through cable:

Standard: 3 x 1.5 mm²

5 wire thru: 7 x 2.5 mm²

Tightening

See page 2

Torques:

Weight:

32W:

6.5Kg

64W

11.4Kg

Stainless Steel LED Linear Luminaire ATEX/IECEx for hazardous areas

SafeSite

Conformity with Standards

This equipment conforms to the standards specified in the

Declaration of Conformity. It has been designed,

manufactured and tested in accordance with BS EN 9001.

Atex Directive 2014/34/EU: Equipment and protective

systems intended for use in potentially explosive

atmospheres. EMC Directive 2014/30/EU Directive for

electromagnetic compatibility.

Equipment Application

This lighting equipment is intended for use in a potentially

explosive atmosphere in Zones 1, 21 and 2, 22 to the

requirements of ATEX Directive 2014/34/EU.

Mounting the Luminaire

Assemble the mounting bracket to the Luminaire with two

M8 x 1.25 by 16mm bolts. Torque specification: 2.0Nm

maximum.

Installation

Ensure that the mains voltage supply is disconnected

before connecting the luminaire. Install the equipment in

accordance with the manufacturer's instructions as well as

any other applicable electric codes.

Always transport and store the equipment in its original

packaging and keep in a dry location. When unpacking

check for any cracks or damage in the housing or lens. If in

doubt, do not install!

The cabling used must be suitable for the site application

and/or the site requirements.

When assembling the cable entries for the mains

connection, always observe the manufacturer's

specifications for the glands used. Unused cable entries

must be closed and sealed by a certified blanking plug.

Note: Unused cable entries must be closed off with a

certified blanking plug or stopper. Dust caps must be

removed and replaced with either a suitable cable gland

or certified blanking plug.

The cable entries should be securely tightened to ensure

that the minimum protection rating is achieved. A locknut is

required for each cable gland to securely hold the cable

gland to the end covers. The cable entry should be rated to

a minimum of IP66/67 to maintain the protection level of

the luminaire.

Do not over tighten as the protection rating may be

compromised. Always refer to the gland manufacturer's

data for torque settings.

Cable gland with O-ring min. thread length C = 10mm.

= M20 x 1.5mm

= M25 x 1.5mm (suffix 4)

The terminal block is suitable for multi-stranded or single

core wires up to a maximum of 4mm

The LIVE, NEUTRAL and EARTH connections are clearly

marked on the terminal block or on a label. Push down at

the 'cross point', insert correct wire and release, ensuring all

the conductor has been securely retained.

3 phase wiring connection

Connect the designated load phase (e.g. L1) to L on the

terminal block and the other 2 live phases to appropriate

live terminals (e.g L2 / L3) on the terminal block as shown in

the diagram.

Loop in /out electrical connections:

Connect incoming cable as above then connect the

outgoing cable to the associated adjoining connection on

the terminal block to pass to the next luminaire. The

outgoing cable may also be connected to the terminal

block at the opposite end to the incoming cable (loop

through)

ONLY SINGLE WIRES TO BE USED ON EACH TERMINAL ENTRY

POINT.

The improper installation, operation, or maintenance of

these luminaries may result in the invalidation of the

warranty, certificate or declaration of conformity.

Taking into Operation

Prior to operating, check the luminaire for its correct

installation in compliance with these operating instructions

and other applicable regulations.

Attention: Only fully certified equipment may be put into

operation.

Conditions for use

The supply to the luminaire must include a fuse which is

capable of interrupting a 1.5kA short circuit current.

When used with steel wired armour or braided cable the

basket weave armour or braid is unable to carry the cable

load without fracture. The cable must therefore be

clamped and cleated to prevent pulling on the cable

being transmitted to the cable terminations.

Improper installation or operation of this luminaire may

invalidate the warranty, certificate or declaration of

conformity. For maximum long term reliability and light

output, the luminaire must be installed in free air.

Maintenance

There are no user serviceable parts inside.

This LED luminaire should require a minimum amount of

maintenance. If any unforeseen repairs are required, please

contact Dialight or its authorised representative.

Inspection

Within the scope of maintenance or inspection routine the

following should be included: Protective hoses covering the

connection cables - cable entries must be free of

corrosion.

Perform visual mechanical and electrical inspections on a

regular basis.

We recommend routine checks to be made on a yearly

basis. Frequency of use and environment should determine

this.

It is recommended to follow an Electrical Preventive

Maintenance Program as described in NFPA 70B:

Recommended Practice for Electrical Equipment.

Repairs / Overhaul / Modification

Should the luminaire enclosure be damaged, only a

replacement will be permitted. In case of doubt, the

equipment should be returned to Dialight for

inspection/repair. Modifications to the device or changes

of its design are not permitted.

The equipment must be operated according to the

intended purpose in a perfect and undamaged condition.

Disposal Recycling

When the apparatus is disposed of, the respective national

, strip length 10mm.

regulations on waste disposal should be observed. WEEE

(Waste electrical & electronic equipment) registration

number W EE/DC2678RY

Dialight, 1501 Route 34 South, Farmingdale, NJ, USA 07727

732 919 3119

Tel:

Fax: 732 751 5778 www.dialight.com

9100127275399 REV A