Dialogic Media Board DM/V600BTEPEQ Посібник з монтажу - Сторінка 2

Переглянути онлайн або завантажити pdf Посібник з монтажу для Мережева карта Dialogic Media Board DM/V600BTEPEQ. Dialogic Media Board DM/V600BTEPEQ 2 сторінки. Dialogic media board quick installation guide

Друкувати сторінку

Power Budgeting is a new feature, introduced in

the PCI Express Specification, that provides a

mechanism to enable a system to negotiate power

consumption requirements for add-in devices.

Per PCI Express Card Electromechanical

Specification Revision 1.0a or higher, a x1 add-in

card can draw no more than 10W in a x1 slot

unless the board's required power is successfully

negotiated and allocated by the system (power

budgeting). However, implementation of power

budgeting by a vendor's system is not a compliance

requirement per the PCI Express Card

Electromechanical Specification Revision 1.0a or

higher. Therefore, some chassis may not support

this feature. Power Budgeting jumper P10 is

designed to ensure proper configuration of the

product.

The DM/V600BTEPEQ Media board must be

installed in a slot that can be allocated 25W.

If Power Budgeting is not implemented by a

vendor's system, the DM/V600BTEPEQ Media board

must be plugged into a x4 or higher slot with the

P10 jumper in position 1-2 (power budgeting

ignored). This is allowed per PCI Express Card

Electromechanical Specification Revision 1.0a or

higher because a x4 or greater slot must be able to

support a minimum of 25W.

If Power Budgeting is implemented by a vendor's

system, the DM/V600BTEPEQ Media board can be

plugged into a x1 slot but the P10 jumper must be

in position pins 2-3 (power budgeting adhered to).

WARNING! Installing the DM/V600BTEPEQ

Media board in a x1 slot with the P10 jumper

in position 1-2 will void the warranty of the

DM/V600BTEPEQ Media board.

If the DM/V600BTEPEQ Media board will be

connected to other telephony boards via a CT Bus

cable, you should install the boards to minimize

unused connectors on the CT Bus cable (in addition

to ensuring that the power requirements are met):

Install boards in adjacent slots whenever

■

possible.

If the DM/V600BTEPEQ Media board will be

■

connected to one or more PCI boards, use the

PCI Express slot(s) closest to the PCI slots.

5. Installing the Board

WARNING! Unplug the equipment before

performing the procedures described here.

Failure to disconnect the power before you

open the chassis can result in personal injury.

Ensure that the system is disconnected from

its power source and from all

Remove

Cover

PCI Express

Plate

Board

Computer

Chassis

PCI Express

Slots

PCI Slots

telecommunications links, networks, or

modem lines whenever the chassis cover is

removed. Do not operate the system with the

cover removed.

CAUTION: To avoid possible damage to the board,

remove power from the computer before beginning

installation. Observe proper anti-static precautions

at all times while handling and installing the board.

To install the DM/V600BTEPEQ Media board,

perform the following steps:

1. Turn off all power to the system and disconnect

the system's power cords.

2. Remove the computer's cover.

3. Choose an empty PCI Express expansion slot

and remove the slot's retaining screw and

access cover plate.

4. Insert the board's edge connector into the bus

slot, and apply firm pressure to the top edge of

the board until the board is fully seated in the

edge connector.

5. Reinstall the retaining screw.

6. Repeat Step 3 through Step 5 for any additional

boards you are installing.

7. Connect the telephony boards together with a

CT Bus cable of the appropriate size (not

included). If possible, use a cable assembly that

matches the number of boards in your system.

If the cable has more than one unused

connector, install the cable so that all the

unused connectors are at one end of the cable.

CT Bus

Colored

Cable

Stripe

(Pin 1)

Note:

Your CT Bus cable may

have a different number of

connectors (drops).

8. Replace the computer's cover.

9. Reconnect the computer's power cord.

6. Connecting to External

Equipment

Each RJ-48C jack on the rear bracket of the DM/

V600BTEPEQ Media board supports a single T1 or

E1 digital network interface. Use an appropriate

cable to connect each RJ-48C jack on the bracket

to your CSU or other network termination

equipment.

The following figure illustrates the pinout of the RJ-

48C jack.

7. After Installing the Board

The DM/V600BTEPEQ Media board requires the use

of a Dialogic

System Software version that

specifically supports it.

If this is the first Dialogic

telecom board you have

installed in your system, you will need to install an

appropriate version of the Dialogic

System

Software and configure the software for the specific

board(s) you are using. Refer to the installation

and configuration documentation that accompanies

the release for instructions.

If you are installing the DM/V600BTEPEQ Media

board in a system that already has the Dialogic

System Software installed, you should verify that

your installed software version supports the board.

If not, you will need to obtain and install a Service

Update that does support the DM/V600BTEPEQ

Pinout for RJ–48C Jacks on

Network Interface

PCI Express Board's Bracket

Cable Connector

RCV_RING

Pin 1

RCV_TIP

Chassis Ground

XMIT_RING

XMIT_TIP

Chassis Ground

Media board before configuring the system for the

newly installed board(s).

Please refer to the Release Update document for

your release version (on the Dialogic Telecom

Support Resources web page) for up-to-date

information about support for PCI Express boards

and any known issues relating to their use.

For technical specifications and product information

go to: http://www.dialogic.com/products.htm.

8. Removing the Board

Removal of the DM/V600BTEPEQ Media board is

essentially the reverse of the installation

procedure:

1. Observe anti-static precautions.

2. Disconnect the telephony cables.

3. Remove the computer's power cord.

4. Remove the computer's cover.

5. Disconnect the CT Bus cable (if applicable).

6. Remove and set aside the board's retaining

screw.

7. Remove the board and place it in static-

protective packaging.

9. Warranty and Return Information

Warranty Period

For specific warranty information for this board,

refer to the Warranty section of the Products page,

located at this URL: http://www.dialogic.com/

warranties/.

Contacting Technical Support

Dialogic provides technical support for its products

through a network of value added distributors who

are trained to answer technical questions on

installing and configuring Dialogic® products. If

you are unsure how to contact your support

channel, please call Dialogic in the United States at

973-967-6600 (9am-5pm EST) and we will assist in

obtaining the appropriate support channel.

Outside the United States please refer to http://

www.dialogic.com/support/contact to obtain local

contact information. Dialogic also provides direct

support via Dialogic

Pro™ Services agreements.

For more details of direct support from Dialogic

please refer to:http://www.dialogic.com/support/

Dialogic Pro

Returning a Product

To return a board for warranty repair or any other

returns, please refer to the following: http://

www.dialogic.com/support/hwfaults.

10. Sales Assistance

If you have a sales question, please contact your

local Sales Representative or the Regional Sales

Office for your area. Address, telephone and fax

numbers, are available at the Dialogic website

located at: http://www.dialogic.com/contact.htm.

To purchase Dialogic® products, please refer to the

following website to locate the appropriate

supplier: http://www.dialogic.com/purchase.htm.

All contents of this document are furnished for informational use

only and are subject to change without notice and do not represent

a commitment on the part of Dialogic Corporation or its subsidiaries

("Dialogic"). Reasonable effort is made to ensure the accuracy of the

information contained in the document. However, Dialogic does not

warrant the accuracy of this information and cannot accept

responsibility for errors, inaccuracies or omissions that may be

contained in this document.

INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION

WITH DIALOGIC® PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED,

BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY

RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN

A SIGNED AGREEMENT BETWEEN YOU AND DIALOGIC, DIALOGIC

ASSUMES NO LIABILITY WHATSOEVER, AND DIALOGIC DISCLAIMS

ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR

USE OF DIALOGIC PRODUCTS INCLUDING LIABILITY OR

WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE,

MERCHANTABILITY, OR INFRINGEMENT OF ANY INTELLECTUAL

PROPERTY RIGHT OF A THIRD PARTY.

Dialogic products are not intended for use in medical, life saving, life

sustaining, critical control or safety systems, or in nuclear facility

applications.

It is possible that the use or implementation of any one of the

concepts, applications, or ideas described in this document, in

marketing collateral produced by or on web pages maintained by

Dialogic may infringe one or more patents or other intellectual

property rights owned by third parties. Dialogic does not provide any

intellectual property licenses with the sale of Dialogic products other

than a license to use such product in accordance with intellectual

property owned or validly licensed by Dialogic and no such licenses

are provided except pursuant to a signed agreement with Dialogic.

More detailed information about such intellectual property is

available from Dialogic's legal department at 9800 Cavendish Blvd.,

5th Floor, Montreal, Quebec, Canada H4M 2V9. Dialogic

encourages all users of its products to procure all necessary

intellectual property licenses required to implement any

concepts or applications and does not condone or encourage

any intellectual property infringement and disclaims any

responsibility related thereto. These intellectual property

licenses may differ from country to country and it is the

responsibility of those who develop the concepts or

applications to be aware of and comply with different

national license requirements.

Dialogic, Diva, Eicon, Eicon Networks, Eiconcard, Dialogic Pro and

SIPcontrol, among others, are either registered trademarks or

trademarks of Dialogic. Dialogic's trademarks may be used publicly

only with permission from Dialogic. Such permission may only be

granted by Dialogic's legal department at 9800 Cavendish Blvd., 5th

Floor, Montreal, Quebec, Canada H4M 2V9. Any authorized use of

Dialogic's trademarks will be subject to full respect of the trademark

guidelines published by Dialogic from time to time and any use of

Dialogic's trademarks requires proper acknowledgement. The names

of actual companies and products mentioned herein are the

trademarks of their respective owners.