ABB Endura AZ40 Інструкція з експлуатації - Сторінка 10
Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Промислове обладнання ABB Endura AZ40. ABB Endura AZ40 16 сторінок. Oxygen and carbon monoxide equivalent (coe) analyzer
Також для ABB Endura AZ40: Посібник (16 сторінок), Інструкція з експлуатації Посібник з експлуатації (20 сторінок)
Друкувати сторінку
8.3.2 Replacing CO sensor assembly gaskets
Referring to Fig. 8.4, page 11:
1. Remove insulation A surrounding COe block B by
loosening insulation retainers C and sliding the insulation
up off the block over COe sensor wires D or, optionally,
remove insulation retainers C and unwrap the insulation
from around COe block assembly B.
CAUTION – Damage to equipment
Appropriate PPE (gloves / goggles) must be worn
when performing this step. The heater block
insulation material is fragile and becomes brittle
after continuous operation. When sliding insulation
away from the CO block or removing it, handle
carefully.
2. Use a small crosshead screwdriver to remove 2 sensor
clamp plate retaining screws / washers E and lift CO
block insulator F and sensor clamp plate G up with CO
sensor H in place.
CAUTION – Damage to equipment
The CO sensor is fragile. The sensor elements
should be protected to ensure no damage or
contamination occurs during this procedure.
3. Take care not to disturb COe heater wires I and use a
small flat-bladed screwdriver to remove thermocouple
retaining screw J (complete with attached washer K)
and carefully remove COe block thermocouple L. Retain
thermocouple for re-use.
CAUTION – Damage to equipment
The thermocouple is fragile and brittle. Handle with
care.
3
4. Use a
/
in. allen key (wrench) to loosen and remove 2
16
COe block retaining screws / washers M.
5. Remove COe block N, preheater O, isolator P, block
gasket Q and isolator gaskets R from flange manifold
S.
6. Remove dilution air restrictor T from isolator P.
7. Carefully remove any gasket material from all surfaces –
a single-edged razor blade can be used.
CAUTION – Damage to equipment
When removing gasket material do not scratch the
surfaces as damage to any internal / mating face
may affect sensor performance.
8. Fit dilution air resrictor T to isolator P.
9. Assemble items N, Q, O, R and P in the correct
order, ensuring the new gaskets Q and R are aligned
correctly.
CAUTION – Damage to equipment
Alignment of the gaskets is critical to ensure a
leak-free assembly. Double-check gaskets / blocks
alignment before securing the COe block to the
manifold.
10
INS/ANAINST/007-EN Rev. B | Endura AZ40 | Sensor assembly | Orifice and seals kit
10. Apply a light coating of an anti-seize compound (suitable
for temperatures up to 200 °C [392 °F]) to the threaded
portions of COe block retaining screws M.
11. Position the COe block assembly on manifold S and use
3
a
/
in. allen key (wrench) to fit and tighten 2 COe block
16
retaining screws / washers M. Tighten the screws
alternately, checking gasket / block alignment during
tightening.
12. Apply a light coating of an anti-seize compound (suitable
for temperatures up to 200 °C [392 °F]) to the threaded
portion of thermocouple retaining screw J.
CAUTION – Damage to equipment
Do not allow anti-seize compound to contaminate
any part of the CO sensor or other local
component(s).
13. Locate COe block thermocouple L ensuring it passes all
the way into the thermocouple hole and use a small
flat-bladed screwdriver to fit thermocouple retaining screw
J (complete with attached washer K).
CAUTION – Damage to equipment
– The thermocouple is fragile and brittle. Do not
bend or break the thermocouple tip.
– When refitting the thermocouple, ensure the
thermocouple wiring is clear of screw J /
attached washer K while tightening to
prevent fraying / nicking of wires.
14. Re-fit COe block insulation A in the reverse order of
removal.
15. Apply a light coating of an anti-seize compound (suitable
for temperatures up to 200 °C [392 °F]) to sensor clamp
plate retaining screws E.
16. Position CO block insulator F with sensor clamp plate
G and CO sensor H in place over COe block N and
use a small crosshead screwdriver to secure 2 sensor
clamp plate retaining screws E to COe block N.
sensor by reversing the removal procedure –
17. Refit the O
2
refer to Section 8.3.1, page 9.
18. Refit the sensor cover – refer to Section 8.2.2, page 8.
19. Refit the probe, exhaust filter, adaptor flange (if fitted) by
reversing the removal procedure – refer to Section 8.1,
page 8.
20. Prepare the sensor for operation by reversing the
shutdown / removal / isolation procedures –
refer to Sections 5 and 4 (pages 4, 4).
CAUTION – Damage to equipment
When re-commissioning the sensor, check the
temperature of the CO block to ensure it is reading
correctly. Perform a manual calibration.