AquaPower AP15AG Посібник користувача - Сторінка 11

Переглянути онлайн або завантажити pdf Посібник користувача для Фільтр для басейну AquaPower AP15AG. AquaPower AP15AG 16 сторінок. Aquapower salt water chlorinator

Друкувати сторінку

Wiring instructions for AquaPower-Plus

All AquaPower-Plus systems are set up to operate at 220 volt from the factory.

Above fround units are set up to operate on 110 volt only. (For above ground

units refer to wiring instructions for above gorund units only.)

To convert a system from 220 volts to 100 volts use the instructions below.

220 Volt Wiring

1. Remove access panel on front of power box.

2. Knock out appropriate hole in bottom of box to match your

conduit size.

3. From your 220 volt power source, install your 2 power lines to terminal 1 and

terminal 4.

Timer wiring for 220 volt pumps

1. Knock out appropriate hole in bottom of box to match your

conduit size.

2. Install (2) power lines to terminal 7 and terminal 8 from your

220 volt pump.

3. Install your ground wire to terminal 6.

Wiring of unit is complete.

110 Volt Wiring

Conversion to 100 volts (In ground pools only!)

1. Remove access panel in front of power box.

2. Knock out appropriaate hole bottom of box to match your conduit size.

3. Remove the (2) jumpers from terminals 2 & 3. Reinstall theses jumpers on

terminals 1 & 2 and terminals 3 & 4.

4. Install your black power line to terminal 4.

5. Install your white neutral line to terminal 1.

6. Install your ground wire to terminal 5.

Timer wiring for 110 Volt pumps.

1. Knock out appropriate hole in bottom of box to match your conduit size.

2. Install your black pump wire to terminal 8.

3. Install your white wire to terminal 7.

4. Install your ground wire to terminal 6.

Wiring of unit is complete.

SPECIAL FUNCTIONS

TO ACTIVATE 24 HOUR BOOST - Automatic super-chlorination

The unit must be in the AUTO mode.

Hold the UP button until the display ﬂashes and the rotating boost mode

indicator will begin.

(The pump & chlorinator will operate at full power for 24Hrs. regardless of

current settings and then switch back to the normal auto mode settings for both

time & output)

• Ideal for periods where pool encounters heavy bather loads

• Avoids the necessity to manually switch unit On and then Off after extended

chlorination periods

PUMP PROTECTION MONITOR

Optional function that protects the pump from operating with little or no water. These

conditions often exist and may damage the pump. The pump protection function uses

the gas sensor in the cell to detect the absence of sufﬁcient water and after a delay

period, the pump is switched off.

TO SET MONITOR: Hold the DOWN button until the display ﬂashes. If a zero is

displayed, this indicates that the pump protection monitor is not activated. While the

display is ﬂashing, use the UP/DOWN buttons to activate the monitor and set the

delay in minutes that you would allow the pump to run in a starved of water condi-

tion. Once set, the display will lock in the value and return to the live display within 30

seconds.

Example: If a delay of 4 minutes is set, the pump will automatically switch off if the

chlorinator cell detects a low water ﬂow for a period of 4 minutes. The message FLO

FAIL-OFF will scroll across the display indicating this condition.

If the unit is in the AUTO mode, the system will retest the condition at the next ON

time period, if the condition no longer exists, the pump will continue to operate as per

normal. Pushing the mode button will also cancel the condition enabling you to oper-

ate the system and determine what the problem is.

All pools have different hydraulic characteristics and risk levels with respect to the

possibility of pump damage occurring due to lack of water. Pumps also have different

tolerance levels to operating dry or in a starved condition. The average delay time

would be from 3 to 6 minutes but we would recommend you seek advice from the

pump manufacturer or a pool professional.

To deactivate the pump monitor, hold the DOWN button until the ﬂashing delay time

is on display. Use the DOWN button to reduce the time to zero, this disables the

protection monitor.

Note: Remember, if you backwash the ﬁlter, vacuum to waste or perform

any other function that bypasses water through the cell, the ﬂow fall

function will switch the pump off after It has timed out since it recognizes

no water ﬂow. Simply push the mode button to reset or deactivate pump

monitor.