Aquascape Pro Signature BioFalls 2500 Інструкції та обслуговування - Сторінка 5

Переглянути онлайн або завантажити pdf Інструкції та обслуговування для Системи фільтрації води Aquascape Pro Signature BioFalls 2500. Aquascape Pro Signature BioFalls 2500 10 сторінок. Waterfall filter

Друкувати сторінку

Aquascape Pro Signature BioFalls 2500 Інструкції та обслуговування

STEP 2

...

CONT

HOOK UP AND LEVEL BIOFALLS

ATTACHING FLEXIBLE PVC PIPE

• The filter is now ready for

the flexible PVC to be glued

into place using PVC cement

specified for use with flexible

piping.

• Prime the inside of the PVC fit-

ting and the outside of the pipe

where the flexible PVC cement

will be applied.

• After priming, apply the cement

to the fitting and the PVC pipe

and fit the two pieces together.

• Hold the pipe into the fitting for at least 60 seconds to

allow the glue to slightly set.

• Wait 10 - 15 minutes to let the glue completely set before you

begin to bury the filter.

• Before you start to backfill around the filter, install the support

racks. Otherwise, you may not be able to get it in place.

Signature Series™ contents diagram on page 3.

• We also recommend having someone stand inside the filter to

keep it in place and level while it's being backfilled.

• The excavated soil from the pond can be backfilled around the

sides and back of the BioFalls

soil while backfilling in order to reduce settling. Any additional soil

can be spread around the far side of the pond in order to create a

planting bed for perennials and annuals.

NOTE: If installing into an existing pond. You may need to bring in extra

dirt to backfill and create a berm around the BioFalls

• Double-check to make sure the BioFalls

installing the plumbing.

INSTALLING THE DRAIN KIT: (OPTIONAL)

1. Prime and glue a stub of PVC Flex Pipe into the fitting on one

of the bulkheads.

2. Prime and glue the ball valve.

3. Attach to the other end of the PVC Flex Pipe.

4. Prime and glue the desired length of PVC Flex Pipe into the

other side of the ball valve and run the pipe to the desired

location to discharge the water when performing water

changes or flushing out the BioFalls

while cleaning

(4)

5. Prime and glue all of the gray valve fittings

and 24" of pipe onto the top of the valve

NOTE: The pipe can be cut down to the desired length

once all of the soil is built up around the filter.

www.aquascapeinc.com |

☎

Refer to

Filter, creating a berm. Tamp the

Filter is still level after

Filter

(5)

CAN 1-866-766-3426 |

☎

STEP 3

ATTACH LINER TO BIOFALLS

There are two options when attaching the lip for the Sig-

nature Series

BioFalls

™

1. The reversible waterfall lip can be attached facing outward.

This method is recommended for first- time installers provid-

ing a solid ledge cantilevering off the front of the BioFalls

Filter to build the waterfall spillway

2. The reversible

waterfall lip can also

be attached facing

inward. This method

allows more creativ-

ity when construct-

ing the waterfalls, al-

lowing the designer

a flat unobstructed

BioFalls

Filter face

for placing large

boulders on the left

and right side of the

unit

(see Ex. 4).

INSTALLING THE

BIOFALLS

FILTER WATERFALL LIP:

• Prior to installing the waterfall lip make sure the face of the

BioFalls

Filter and liner is clean and free of dust and debris.

Use a damp towel to clean both surfaces

• Hold the liner up against the face of the BioFalls

ing the U-shape spillway opening. Be sure to leave slack at

the base of the filter to avoid stretching the liner when rocks

are stacked to build the waterfalls. (continued on pg. 6)

US 1-866-877-6637

FILTER

Filter:

(see Ex. 3).

Ex. 3 The reversible waterfall lip attached facing

outward

Ex. 4 The reversible waterfall lip attached facing

inward

Filter, cover-