Aquatec Equipment EV1910LV-DC Інструкція з експлуатації - Сторінка 4

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Водяний насос Aquatec Equipment EV1910LV-DC. Aquatec Equipment EV1910LV-DC 13 сторінок. Low voltage submersible water pump & dc power supply

Друкувати сторінку

IMPORTANT SAFEGUARDS

Please read the operating instructions and familiarise yourself with the equipment before placing it

in service. Correct and safe use of the system requires strict compliance with the safety instructions.

For safety reasons, persons less than 16 years of age or infirm persons that are not familiar with these

instructions should not use this equipment.

• Any damage to the equipment or unmerited operation

will bring dangers to the surrounding precincts. So if

there is any damage of the equipment, it must not to

be used. The equipment should be placed out of reach

of children.

• For your own safety, disconnect from the power supply

before any maintenance of any equipment is attempted

on the tank or water body. Always unplug the pump

from the power supply when not in use. Never pull the

cable to disconnect the plug from the power supply -

Grasp the plug and pull to disconnect. If required, have

a qualified electrician install a weatherproof power

supply point near to the pond or water-feature (within

the cable length of the appliance).

• Be sure the equipment is submerged completely in the

water. The depth should not be greater than 2m.

• Do not operate the pump if the appliance or any

components of the system, such as the power cable,

have been damaged. Check appliance for defects

regularly.

• Always use a properly grounded power supply that is

connected to an RCD with a rated residual operating

current not exceeding 30mA. As per AS/NZS

3350.2.41:1997

PRODUCT SPECIFIC SAFEGUARDS

• Do not operate the pump without water at any time,

permanent damage may occur.

• Be sure the equipment is submerged completely in the

water. The depth should not be greater than 2m. If used

in line, the pump must have adequate flooded suction

at all times.

• The pump is designed to be used in a Garden pond/

waterfeature or Aquarium environment. It is not to be

used in any other manner or purpose.

• The pump should only be used in clean water. Do not

use the pump in, or with, any chemicals such as a

solvent or gasoline.

• All PondMax Submersible pumps are cooled by water

flowing through the inside of the motor body. If the

pump flow becomes restricted it will overheat and could

cause permanent damage. Large tubing size is strongly

recommended to deliver adequate water flow to cool

the pump.

PMAX EVOII 1910_2910_3910_4910 DC Pump Instructions.indd 4

• To avoid an electric shock, do not attach the plug to

the power supply socket with wet hands. The drip loop

method should be used to prevent water from traveling

down the cable and onto the plug or power supply.

If the plug does get wet, do not unplug the cable.

Disconnect the circuit breaker that supplies power to

the power supply point. Then unplug and examine the

plug and power supply point for presence of water. If

the power point has become wet, you should consult an

electrician before using the power point again.

• Do not install or store the appliance where it will be

exposed to extreme hot or cold temperatures. Do not

use in water above 35°C.

• Do not cut the cable as this will result in voiding your

warranty.

• Care should be taken to arrange the power cable so

that it cannot be accidentally tripped over or pulled.

• Do not attempt to repair the electrical appliance

yourself. Return to an authorized service centre or place

of purchase if a fault occurs, (regular maintenance is not

considered repair and is required by user).

• These pumps are strictly 12V DC Current. Power

fluctuations greater than 10% will damage the motor

and void the warranty. Do not use any other power

supply other than the one supplied.

• The pump needs to be cleaned regularly to prevent the

pump becoming blocked, thus causing the pump to

overheat and burn out. This is not a warrantable event.

It is strongly recommended not to select a pump that

is too small for the Job required. The flow rate through

the pump needs to be enough so that a half of the rated

max flow is kept running at all times.

• The 2 Pin Connector can only be connected one way.

Ensure the connectors are correct to ensure power

alignment.

A Q U A T E C E Q U I P M E N T . C O M

22/12/16 7:33 am