Aquatec Equipment AQUAPRO AP2400F Інструкція з експлуатації - Сторінка 3

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Насоси для ставків Aquatec Equipment AQUAPRO AP2400F. Aquatec Equipment AQUAPRO AP2400F 5 сторінок. Pond & fountain pump

Друкувати сторінку

INSTALLATION

• Once a fountain nozzle has been selected, assemble the fountain kit as per the diagram.

• Screw the T-piece onto the pump outlet and adjust the telescopic riser to the desired height and align vertically. On

the Dual Control Flow Adjuster, on the T-piece, you can vary the flow between the fountain head and the waterfall

outlet. Close the second outlet of the T-piece if this is not required for an optional waterfall or water spout.

• Place the pump in desired location, ensure the pump is on a stable surface that is free of sludge, sand and other

debris, and connect tubing to the outlet or attach fountain kit.

• Position the device in the pond horizontally, on a solid base, in such a way that it is fully covered with water and the

fountain nozzle protruding out of the water.

• Push the plug into the power supply outlet and switch on.

• Use the power supply switch for turning the unit on and off.

CLEANING INSTRUCTIONS

Begin by ensuring that the mains power supply is disconnected before attempting any maintenance or adjustment of

the unit. Remove the unit from the water. The ﬁlters and sponges in this unit will clog over time. Please clean regularly

(at least once a month) to ensure strong water ﬂow. Failure to maintain the unit will result in a burnt out motor and

other damage.

All AQUAPRO Pond & Fountain pumps are water cooled, if pump becomes restricted, or blocked, it will overheat and

could cause permanent damage. The motor unit of the pump is encapsulated with epoxy resin and does not need

lubrication. Regular inspections, cleaning and maintenance of impellor is necessary to ensure longer impellor life.

• Take off the fountain set first. Unscrew the fountain kit

from the top of the unit. Examine the nozzles to ensure

all ports are unblocked. Clean with a suitable brush if

necessary.

• Maintain the filter sponge regularly according to how

quickly the sponge gets clogged up. When the flow

starts to be reduced, check and clean if necessary.

• Unclip the front filter cage from the front of the pump

and take out the filter sponge and clean. If using an

optional prefilter block sponge, slide the sponge off the

threaded core and wash out. It is recommended that

this is done in a bucket of pond water to ensure the

good bacteria that are present in the sponge are not

killed by the Chlorine in tap water. Check for wear and

tear of the sponges. Replace if necessary.

• You can help boost the biological function of your filter

sponge with a bacterial additive, available from your

local stockiest.

• To maintain the impellor of the pump, turn the Impellor

cover locking ring in an anti-clockwise direction to

the stop position and lift off. Then you can separate

the impellor cover from the pump body. Take out the

impellor. (Take care not to break ceramic shaft because

it is brittle.)

A Q U A T E C E Q U I P M E N T . C O M

AQP AP1000F_AP2400F Instructions.indd 5

• Clean the impellor with clean water and a suitable

brush. Inspect for signs for wear and tear. If the

impellor set becomes worn or damaged it should be

replaced (available from your dealer or special orders).

Failure to do so may cause serious damage to pump.

The impellor set is a wearing consumable part.

• Once the cleaning and inspection process is completed,

reassemble in the revers manner. Reinstall the shaft

into the motor body, and then carefully slide the

impellor onto the shaft. The impellor will pull itself in by

magnetic force, this is normal (take care not to pinch

your fingers or break the shaft).

• Replace the impellor cover, making sure the shaft is

located properly on the impellor cover. You may need

to place rubber impellor locator (Grommet) on end of

shaft to locate into impellor cover properly. Reattach

the locking ring.

• Replace the internal sponge and front cage or foam

block sponge prefilter.

• Re-attach fountain kit and/or tubing, relocate in water,

connect to power supply and turn on.

AP1000F & AP2400F

POND & FOUNTAIN PUMP

A Q U A T E C E Q U I P M E N T . C O M

23/10/2015 7:17 AM